Search results for query: *

Happening Saturday 6/22/24

@barracudadave67 I only used the rear passenger regulator. I've just kept everything else, mostly in your original packaging from 2015. Funny enough, cleaning the garage yesterday and snapped a picture.

Thank you for the help, everyone. There appears to have been two different problems—electrical and tuning. The electrical seems to be resolved by replacing a broken eye connector and tightening the starter cable. The symptoms of shortening out when starting has not reoccurred. I was...

Sorry, I didn't answer. #17 Yes, gas squirts after it dies.

Here are a couple of videos 1st is a cold start. Car fires off and then cuts off after a short amount of time. 2nd start - idle to 2k After the brief running, there is gas in the fuel line. I changed out the fuel filter wishing/hoping it was clogged.

The MSD distributor was configured back in early 2020 (with a tweak or two soon after) I am using two light blue springs for the advance rate and have the black (18 degrees) bushing installed. 16 degrees of initial and 34 degrees of total advance. Cam information 110 Separation with @50...

Thank you Super-Cuda, I will look into these tests. In the short term, I checked the distributor for any issues, but none were visible. One of the screws holding the rotor "seemed" loose. Afterward, I decided to start the car and last minute make a crappy video. Sorry for the quality. It...

I stole some time to work on the car. The positive connection was loose. I tightened it about a 1/4 turn. Checked all other connections and everything looks good. All grounds are in place and good condition. The car fires up with no problem but I am not able to keep it running before it dies...

following - with same AFR gauge

Quick update. Bad battery connections made sense to me. Currently running an Optima battery which has smaller diameter posts than traditional batteries. And the Optima battery is a couple of years old. Swapped out to a traditional battery, the car fired up first try however, it exhibited a...

Wow, I hope it is the battery. I have an extra battery to test when I get home. The battery in the car has been on battery tender when not in use.

The distributor is a MSD Ready-to-Run that has been on the motor for 6 years. There has not been any work in that area for a long time. Timing was adjusted 6+ months ago

Looking for some help tracking down an electrical gremlin that popped up this weekend. Backstory The 66 Barracuda hasn’t been driven a lot for reasons unrelated to the car. Other than that, the car was in great running order. Normal stating process: remove from trickle charger, partially...

Installing the console back into my 66 Barracuda, I broke the automatic shifter pawl. This is the wire inside the shifter that is depressed to change gears. See pictures Is that a replaceable part? How hard is it to replace? Looking around, I have not found that part for sale. Help and...

Mark your calendars the Mopar Alley - Mopar Rally is Saturday June 22nd

Do these look like the correct screws?

Hello, I am working on installing a console in my Barracuda. The attaching 4 screws are missing. Can anyone help with size and/or show a picture? It seems these would be #6 screws

Hello, I am looking for a manual steering column for my 1966 barracuda. Working condition preferable

Hello, I am looking to change to a manual steering column on my 1966 Barracuda. And of course, these early A columns are getting hard to find. I am curious is there a mounting bracket difference between the early A column and the 1970-76 column? I can get a Flaming River "no key" manual...

I did not. Under hard acceleration, you could feel/hear the shift to 2nd which isn't too bad and smooth into drive(3rd) Dynamic converter built my 904 with a manual valve body and my converter. My car is a column shift and the shift pattern sucked. Probably my fault on ordering. Dynamic...

Very nice car, love the green. You have a lot more power than I am running. Mine is a 408 stocker around 470hp at the crank. You should call John and chat with him to get the proper parts

Thanks @4spdragtop I sent him a PM.

A while ago, there was a member that did custom pint glass engraving. I lost his contact information. If someone has it, can they pass it on to me?

Always a great show. Hopefully, the number of cars will increase from last year, since we are further away from all the covid craziness. Mark you calendar

Kind of a slow process, but I finally ordered my data logger DI-2108 8-channel High Speed USB Data Acquisition System I am sure I could have found a cheaper one, but I know this will do everything I want. It will graph the Air/Fuel meter results with RPM as the y-axis. And of course...

Quick update. I bought the wireless sensor kit. My plan is to have this as an external tool that I will use during carburetor tuning and calibration. And of course, I can take this mobile for drag racing or to help friends. The initial testing was pretty informative, I need to tweak a few...

Yes phone, ipad laptop over bluetooth.

I've been following this tool for some time now and wanted to reach out to see if anyone has any experience with this wideband kit or something similar. https://www.summitracing.com/parts/fst-170302 It is expensive. However, I have two carbureted cars and several friends that tune and...

Big Thanks @Rat Bastid I finally made the regulator swap to the Mallory 29388. It wasn't a drop-in for me, I had to find a mounting bracket to modify and many excuses later before I finally installed the regulator a couple of weeks ago. After the initial pressure adjustment, I have not had...

$40 or best offer plus shipping