Search results for query: *

Also looking for: 1. Horns 2. Sun visors depending on color and condition 3. Grill center section

The stabilizers are the "or these", the second picture. Thanks.

1. Is the carpeting for an automatic or 4 speed? 2. Who is the carpet manufacturer? 3. Do you have the front bumper stabilizers? These are the "Z" shaped bars between the bumper and the fender. 4. I'll take the front speaker frame.

Does anyone know of any upcoming sales for interior items: seat covers, carpet, buns, headliner? Thanks, Ken

If still available, I'll take it. Ken

Thanks. I have seen the split loom. They all appear to be a plastic mesh, not cloth. I was more interested in cloth but may have settle on the plastic mesh.

I am building a new rear (trunk) wiring harness for my ’64 Barracuda. The wires are presently in a cloth loom. Does anyone know of a source for the cloth loom? I have been unable to find one that looks like what I have now. Could it possibly be what is called an asphalt coated loom? But there is...

I have purchase new correct grommets for my ’64 Barracuda E-brake cable and speedometer cable. The end fittings on both are considerably larger than the hole in the grommet. Has anyone installed these grommets or has advice on installing them. Photos attached. Thanks, Ken

Is the lamp socket separable from the housing on a '64 '65 Barracuda front lamp assembly? If separable does anyone sell or have the socket assembly (socket and pigtail)? Thanks, Ken

Replacing the parking brake cable on my '64 Barracuda. The old cable is broken off just behind the cross member supporting the transmission. I need to replace the entire cable. The cable sheath is throughly rusted to the cross member. Does anyone have experience or advise in removing the brake...

Looking for both right and left front fenders for a '65 Valiant. Thanks, Ken

Does anyone have or know of a cross reference for Mopar hardware? I'm looking for a list of Mopar 6 or 7 digit part numbers converted to common hardware descriptions. Examples: 446363 = 3/8" Type A flat washer 9421589 = 1/4-20 Pan head screw Thanks, Ken

Just noticed this ad. If not sold, I'll take them.

With the current pricing you are right JDM.:eek:

Getting ready to buy carpet, seat upholstery and buns for my ’64 Barracuda. ACC and Legendary. Does any vendor have a sale going on now? Or do you know of an upcoming sale? Thanks, Ken

I am in the process of repairing/rebuilding the wiring harnesses on my ’64 Barracuda. Need help identifying this part. It is part of the body wiring harness (wiring in the trunk) and is located just forward of the jack. It appears to be molded over the wires and is part of the wiring loom. What...

Still doing some planning for rebuilding my engine compartment wiring harness. It seems that the weak spot in the wiring is taking the full current through the bulkhead fitting to the ammeter. I plan on using headlight relays to cut down on some of the current. The wiring “killer” appears to be...

The ballast resistor is a single. The ECU is an original "Orange box" manufactured in 2004.

Working on my '64 Barracuda wiring. In checking old threads I have found conflicting information (don't figure) concerning wiring up a dual field alternator, an electronic voltage regulator and an electronic ignition kit. I believe that the attached sketch shows the correct wiring. Could any of...

Rebuilding the dash wiring harnesses on my ’64 Barracuda. Am looking for a part number, description, and source for the female terminals in the printed circuit board female connector (P/N 2258651). The actual female terminals are 5/8” long and fit over 3/32” diameter pins. Also looking for a...

I am considering building (rebuilding) an engine & forward wiring harness for my ’64 Barracuda. Electronic voltage regulator (3438150), Electronic ignition kit (P3690426) and mid ‘70s square back dual field alternator. Questions: Are there any downsides of increasing the wire sizes in the...

This part fell on the ground as I was disassembling the bucket seats on my '64 Barracuda. What is it and where does it go? Any help will be greatly appreciated.

I have a '74 360 and am using a 90* oil filter adapter. I don't believe that I need or can use the oil filter adapter plate. I need a conformation from FABO gurus.

I would like some advice from FABO members. I’m finishing up the final assembly of a ’74 360 which will go into my ’64 Barracuda. Of course, I can’t find the water pump pulley. The original engine had PS and AC, neither of which I am going to use. The existing alternator pulley has 2 grooves...

New glass. Not near the glass today. Attached is picture of the sticker attached to the glass. Too bad nothing is make in the USA anymore.

I would like to give a thumbs up to VintageGlass.com. Needed a windshield for my '64 Barracuda. I wanted non-tinted. Found several other vendors that only had them with a tint or the dark blue strip. Vintage could supply all three styles. Had it quoted and I sent an email ordering it on April 30...

Thanks. The yellow bushings fit as advertised and make sense. And no air injectors on the '74 heads.

Attached pic is of some engine gaskets that I can not identify. Engine is a '74 360. Gaskets are from a McCord gasket set 95-3038. I don't know if I don't need them for that year or what? Thanks in advance.

Has anyone dealt with Vintageglass.com?

Does anyone have the location of the rear seat hold down brackets for a ’64 Barracuda? Mine were removed when the floor pans were replaced. Thanks in advance.