Search results for query: *

'68 Barracuda - Carter BBD4421S 2bbl carb. The car suddenly began to idle terribly. Much testing and head scratching. New plugs, fuel filter, fuel pump, and coil didn't solve it. Adjusting dwell and timing didn't solve it. I hooked up an extra plug to each wire, one by one and verified that all...

So I've got this listed on eBay for $225. Anybody interested? The unit is correct for all 67 to 68 Mopar A B & C body with Dealer installed A/C, including: Valiant Barracuda Dart Belvedere Satellite Coronet Charger Fury Polara Monaco Chrysler Imperial.

Does anyone know of an R-12 relaimation service near Wilmington NC? I need to remove the R-12 from my old Barracuda to replace the expansion valve, then re-install it.

Repops brand. Had this piece left over from my full kit. New, perfect condition. $10 plus shipping.

Can anyone tell me the correct fitment of the door windlace. Is it supposed to go up underneath the trim as shown here, or is it supposed to stop just short of it? I'm reinstalling the window interior trim piece and it just doesn't seem to fit right with the windlace jammed up underneath it. Thanks.

This MOPAR starter was used on a wide variety of '62-'69 Dodge, Plymouth, and Chrysler vehicles. There were probably millions of them made, but this one has a 442 date code on the armature housing, indicating the 44th week of 1962. The starter drive casting, P/N 2095219, has a date code of 1964...

Well I have this Mopar fan motor......but it is quite a conundrum. I removed this motor from the under dash a/c system on my wife's one-owner '68 Barracuda; she has never had it replaced. It is a double shaft motor and with 12 v applied, spins like new at 3850 rpm. The motor is quiet and the...

Well I have this motor......but it is quite a conundrum. I removed this motor from the under dash a/c system on my wife's one-owner '68 Barracuda; she has never had it replaced. It is a double shaft motor and with 12 v applied, spins like new at 3850 rpm. The motor is quiet and the bushings seem...

Does anybody have any for sale? Thanks

Looking for a good timing chain cover for my Barracuda. Casting # 2128896. No corrosion on gasket surfaces. Thanks

I have 2 Gabriel Hi-Jacker shocks from the rear of my '68 Barracuda, P/N 729706. The wife thought the ride was too stiff so I took them off. One of the air bladders appears to be leaking, but the fluid side works fine on both. Comes with all the tubes and connectors. Just want to cover postage...

I have a set of original front seat arm rest bases from my '68 Cuda. I have since bought aftermarket ones and have these left over. They probably need re-chromed and one has a small crack in a radius, not visible when installed. Otherwise in great shape for a driver. Any interest? Make me an offer.

Rear bumper brackets from 68 Barracuda. Blasted and painted black. Original MOPAR. $20 plus ship. PM me.

The door window has a metal frame portion on the rear vertical edge. The frame is glued to the glass. The frame has a rubber seal/weatherstrip attached to it to seal the front window to the quarter window when both are closed. Anybody know what this seal/weatherstrip is called, and where I can...

These are L & R undamaged OEM, blasted and painted black, ready to mount. I bought these for my '68, but ended up straightening the originals and using them. Need $35 + shipping. Thanks

Anyone know the correct torque for the bumper-to-mounting bracket bolts for '68 Barracuda? I was re-installing my repaired bumper, got to about 25 ft-lb and the head snapped off the first bolt. These are the round-head bolts that fit into the square hole in the bumper. Thanks

OK, here's the scoop on this fender. My '68 fender was damaged during a movie shoot so looked far and wide for a replacement, had to be OEM and in excellent condition. Bought this '67 fender from a gentleman in Arkansas thinking to convert it to '68. My body man convinced me to repair my...

Need RF (passenger side) fender for 1968 Plymouth Barracuda ASAP. OEM preferred. Must be in good restorable shape; no rot, extra holes, dents, or major rust. Please reply with contact info, description, location, and price. Thanks, Greg