Search results for query: *

cant u just add vented gas cap? i think gates makes one that looks stockish

well u were right both + and - shows continuty to coil chasing

well the car is 71 dart. i did connect two terminals from ballast together. hooked up the old coil + to swiched 12v. i tried my old coil and got spark. then i took the new coil out off the new braket and now it also gives spark.

well i figured it out. is was my new coil bracket squeecing the coil too hard -.-

I installed pertronix hp ignition box and flamethrower 3 coil. Now i dont have spark. I get power to box and its plinking Green when cranking. I have measured switched power is ok and main power and ground are on battery. Should there be voltage at coil +? I dont

hello! so this is prob stupid guestion but can i change springs in my distributor and add limiter plate while distributor is in car or do i have to remove it.ty :=) car has -70 sbm

Yeah it reads on regisration license...

Yeah i think car dosnt pass inspection if i swich to manual brake.

I have low vacuum from engine because cam, brakes are hard when first starting to drive the car. What do you suggest i do for my power brakes? I have looked at leed`s vacuum pump but is there anything else *** good but not so pricey.

atleast on my 71 abody i unscrew 3 bolts from the colum (with the white plastic washers) and 3 bolts at firewall. then remove screws from cluster and maybe from the heater bezel. now u can pull cluster a little bit out and remove the electric connectors from both sides+ the amp gauge studs and...

Hello. Im thinking deleting my ballast resistor because im planning going to holley sniper. I like to know if my current ballast is wired correctly and can i just wire the poles together and get 12v switched from that. I know i need new coil that dosent require ballast but can the mopar Orange...

So i have 904 transmission with lokar kickdown cabble. Problem is the trans kickdown lever dosent fully go back when i let off thortle. if i crawl under the car i can push the lever like half inc towards the engine. Im thinking of adding spring to lever. but should kickdown lever be completly...

Can anyone recomend pcv valve for low vacuum. I know about the mevagner valve buy thats like 200 euros when shipped to me....

okey i drilled the secondaries with 3mm holes. now my mixture screws work! but i have another problem... now when i pump the gas the rpm stays high for like 5seconds before coming back down. tried to find vac leak and even did new carb and spacer gasgets. could too big drilled holes cause rpm to...

hey sorry for taking so long me to reply but been kinda busy. tomorrow i will be taking the carp of and checking the float and prob start drilling. one thing. why to drill secondarys and not primarys? thanks :)

dodge dart swinger 71. automatic 904. sorry dont know what gear is in it nor the comp ratio. no havent checked compression.

thanks so much for help so far. im sorry what more details you like to know?

And i dont realy wanna buy new carb because im thinking of upgrading to sniper maybe next summer

the shaking was there before and after the pcv. and i tried to adjust the idlemix after putting the pcv back. but okey tomorrow i trie to move the fan or radiator closer together. alredy have one diy fan spacer installed but its only like 1inches thick

oh yeah forgot to mention heads.i think they from 360 with some heavier springs.

okey specs for car first. dart 71 318 scat i-beams kb flat top pistons comp cams nostalgia plus pn#20-670-20 int.dur.adv 280 exh.dur.adv 287 exh. valve lift 0.474 int. valve lift 0.474 speedermaster intake edelbrock 1405 carb mopar elec ign vac advence is disconnect and base timing is about 20...

maybe its like winter position then

how does that work? it makes thermostat to be a plug? where would u need that? im asking because i have that kind of thermostat in my car

okey i got the turn signals working again but now car only starts on neutral and not park. do i need to recenter stearing colum somehow? wicth i dropped before to get cluster out :o

okey thank you for that :)

Okey thanks :o but now i have once again problem. When i put dash back together my turn signals No longer work. I have measure the turn signal relay and there is No power coming to it. Then i disconnected the under colum coupling and measured pins coming from steering wheel and there is No power...

Question once More... Does anybody know is these wired correctly. Black and Orange switches places and 2 blacks goes for nothing. Thanks In advance :)

Thanks everybody for help:) I think i got ign 2 working by cleaning the bulkhead connector does anybody know what this is? It takes power from fuse box BEFORE fuses.

well i installed new solid state limiter. bench tested the whole instrument cluster and everything worked. Then i putted it in car and nothing worked, even not the turn signals wich worked before. no power to anything, when starting it would crank for like .5 seconds. In one point it started...

for sensor i checked connection from the body of the sensor to battery - and it has connection. and then i checked ohms from sensor body to the 1 pin and it didint show anything. Does that mean sensor is bad?