Search results for query: *

Went from Hoosier 28X10-15 to Mickey Thompson 28x10.5-15. Actually had more space between the tires and the springs. Running 3/4 shackles. I know it looks close but they have never touched. Sorry the tire pic looks like crap. Just walked out in the rain to take it.

Nevermind found it on FABO 2 mins after posted.

Searched google but can't find it. Need the size for the 3 screws that hold the filter to the valve body of a 727 with shallow pan. Lost the old screws and installing transmission today.

Does anyone make a bracket to put the alternator on the driver side of a small block. It's going into a 71 race car and would like to run a short wire to the +side starter post. Is it possible to use the factory brackets and turn them around so it work on the driver side?

Dont know if im in right section with this question, but does anyone know what size the front wheel studs are for a 71 Duster with drum brakes? Need to change out the wheel studs and dont know the size.

Do you know if there is a link or a write-up about putting one in the k-frame?

Has anyone installed a manual rack and pinion into an A-body. I have fab skills and know that it wont be a "bolt-in" But just trying to get ideas how you mounted it. brand, size, u-joint lengths. Adapters. Any info would help and pics would make wonders. Thanks

It has accel pumps but not sure about the power valves. It does have a boost reference port on the side of the main body. Not sure if i can cap that off or what all I would have to do. I know I should just buy the correct one but honestly dont have the money for that.

I have a new 750 cfm supercharger carb and wondering what mods need to be done to make it work on a n/a engine.

If your talking about a 6.1 from Mopar, they do not come with a tensioner.

The Dayco has better tension vs the rest. When my company (High Horse Performance) installs superchargers on the SRT cars we only use Dayco tensioners because we have seen the factory, ACdelco, off brands, etc. literally explode. Unless your going the supercharger route you dont "need" it but we...

Still available.

Does someone have a like to a how to remove and install lca and torsion bar on a 71 duster?

Would perfer a 741 or 489 case. Not concered about what diff is in it cause im going to put a spool in.

Looking for a 8.75 center section from someone in the charleston, sc area.

yes and havnt found anything that had good quality

Does anyone have a sound clip of there Mopar running spintech mufflers. Ran them on my dakota and thinking about putting them on my duster with a X pipe.

Sorry about the blurry pics.

They are a real good tire for street use on DRY roads. Im posting pics of some cars that we built at High Horse Performance Carolina that ran them when it was raining and neither one of them was "hot rodding". The GTO I just drove up to Jacksonville, NC today to pic up and bring back to the shop.

I have a 360 LA with RHS heads, hyper 10.5-1 pistons, eagle rods, mopar factory strok crank, ARP bolts, and thinking about throwing a turbo on it and wondering how much boost do you think it could handle and still be kinda safe. lol

Also have a Carter Thermoquad 6-2643. Brand new in box, never bolted, Holley reman carb that I would like to get $150 obo. I will post pics on here when I get home tonight. Comes with gaskets, Holley box, and Holley instrtuction manuel.

I will have to check when I get back to my house tonight.

I have 1 bucket seat that came out of my Dart that I am trying to sell to finish my race car. It is in good condition. There are no rips or tears. Should clean up nice with a good upholstery cleaner. The hinge covers need to be replaced as they are dry rotted. Would like to get $100+shipping obo...

I have a Holley 650 part number 6210-3 that needs to be rebuilt, it's been sitting in my garage for years. Don't know what they go for so im going to say $75+shipping. Also have a Carter AVS that came off my 360. Not sure if it is a 600 or 650. Works great, does not need a rebuild. Im going to...

Does Timkin make some? I get a deal with my shop.

Who makes them and what is the part number for them for a 8 3/4.

I would Strongly suggest staying away from chrome on a aluminum intake. Her is a pic of my chrome water neck that came off my LD340 intake after about 5000 miles. Started getting a coolant leak and couldnt figure out why until it left me stranded after I thought I got it fix. Replaced it with a...

im about 99.9% sure they are stock.

hopefully you can see what im talking about in these pics

bare with me as im getting pictures sent from my phone to email and getting them posted