Search results for query: *

still need Ford 150 run from Las Vegas to Savannah Ga.

Need to get a running Ford F-150 from Las Vegas to Savannah ga

The left (driver's) side is different between a 318 and a 340/360. There is an ear missing. The passenger side is the same on 273,318,340 and 360.

I may need someone to deliver a b body fender from Chryslers at Carlisle in July to Cedar Rapids Iowa

I've seen topics like this before but never paid attention until it now involved me! I need to ship a Belvedere fender from south GA to Iowa. I'm certain Fedex & UPS do not handle anything that large? What are the pros and cons of Greyhound? Any other ideas? Thanks in advance! Greg

I would think that if you have the 73-up steel bumper reinforcements with the shock absorbers you could bolt/weld directly to the bumper brackets!

USPS has a special "media mail" rate for printed materials, books and videotapes/cds. It should go under $5 with that rate.

It is with deep sadness than I announce to the Mopar community the death of one of my best friends, Mike Buhrman AKA Mountain Man of Thurmont, MD. Mike passed away Saturday April 4th, shortly after his 65th birthday of congestive heart failure (not COVID 19 related) His wife Judy has asked...

Thank you! Ad modified.

This is a factory vehicle Certicard & holder. I'm told it's from a 67 Belvedere/Satellite. It's in fair to good condition. The holder has one stud missing. You can mount "as is" or use two sided emblem tape. Located in Savannah, GA I need to get $20 shipped (in the US) Thanks for looking!

Brewer's Performance - Mopar A833 4-Speed Transmission and Component Specialists

Still available if you can pay immediately with Paypal.

This is a good used torque shaft (Z bar) for a 70-74 E body or a 71-74 B body with a BIG BLOCK 4 speed. This is the linkage bar that goes from the frame to the bellhousing. The rod from the clutch pedal attaches to one side and the rod to the clutch fork attaches to the other side. This piece...

This is a good used torque shaft (Z bar) for a 67-76 A body with a small block v8. This is the linkage bar that goes from the side of the body to the bellhousing. The rod from the clutch pedal attaches to one side and the rod to the clutch fork attaches to the other side. This piece has been...

sold. Thanks!

It uses the standard 67-76 A body ballstud and inner fender reinforcement bracket. If your car is currently (or was from the factory) a standard transmission vehicle. it will already be on the car. If you are converting from an automatic you will need to weld on the bracket. I have the...

I still have a few of these left :)

Brewer's Performance - Mopar A833 4-Speed Transmission and Component Specialists Brewers website lists the spring for $49.95. Brewer's Performance - Mopar A833 4-Speed Transmission and Component Specialists The hook is $14.95

List them singularly. They still have value if someone is swapping down from a 340/360. Only the left side is different. You might get $15-25 each plus the ride for them

Ok, I'm lowering the price to $100 plus shipping. This is an original Z bar, the special bracket and the spacer from a 67 383 4 speed Barracuda with a 10 1/2 inch bellhousing. ( I took it off myself) I have one of the attaching bolts (standard replacement bolt can be bought at a hardware...

They are both left (driver)side mounts for a 318. NOT a set. The one with the missing ear is a 67-72 A body. The other is a 318 66-72 B and 70-74 E body.

.I have one good vent bolt and three brass fittings left (one "Y" and two "V") I also have a number of vent bolts that don't have the "check valve" working or the top cap is missing. These would attach the brass block to the rear and vent the housing if you were not picky. So any one block with...

I polished and clear coated some of mine. Selling clean ones for $18 plus the ride: [FOR SALE] - 8 3/4 Brass Brake T Fitting & Vent Tube $18 plus shipping "

This is the pushrod that goes from the master cylinder to the brake pedal on a 66-70 B body with manual (non power) brakes. The special bolt is also included. This hard to get piece has been wire wheeled and painted with Cast Blast. Located in Savannah, GA I'd like to get $15 plus shipping ($8...

After a few requests I've finally cleaned up some of my used 8 3/4 brake line fittings. They are brass and polish up very nicely on the wire wheel. After that, I clear coat them to keep them that way. I also have the special vent bolts that have a "check valve" in them. This is the fitting that...

I have ONE new Magnum 500 wheel center cap with the "Bull's Eye" design used on Mopars. I do not know if it's nos or repro, but since I don't see a part number, please assume the latter. It has the retainer but one of the screws is missing. Again this is ONE cap that I got in a box of parts...

Mine are used originals and I have a couple of sets. Thanks!

I have a set of 2 used torsion bar adjuster blocks and bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US...

I have a set of 4 used upper control arm cam bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US. Merry...

I have one used set of lower control arm pivot studs with the correct washers/nuts for a 66-72 B body or a 70-74 E body. The threads are in excellent condition. The studs have been sandblasted, wire wheeled & painted with Cast Blast and are ready to install. Located in Savannah, GA I'd like to...