Search results for query: *

  1. A

    [SOLD] Hood Scoops

    Original mopar or repros? Shipping to Canada Okay? Your PM,s are full.
  3. A

    1972 DODGE DART SWINGER 340 4 spd $12000

    Purchased from original, elderley owner from Yucca Valley California. -originally 318 auto car no rust -1970 TA 340 X heads -750 Demon carb -Edelbrock RPM intake -MSN Ready to run dist,wires,coil -Dougs headers -TTI 2.5" X exhaust system -Completely built 8 3/4 sure grip 4.10 BBP -A833...
  4. A

    Z-bar frame ballstud bracket location/repair help

    I agree with Brad I also used 1/4" steel plate cut to apropriate size works better than original much stiffer stiffer is always better:finga:
  5. A

    LCA bump stop clearance?

    Your cars stance looks nice about the same as mine, If i want it to sit lower it is going to be sitting on the rubber stop? seen lots off other darts set up like this but it limits pivot in the LCA? Doesnt seem right to me?
  6. A

    LCA bump stop clearance?

    I just noticed that my car is pretty much resting on the frame i adjusted it to about a 3/4" gap just not sure if thats enough or not?
  8. A

    LCA bump stop clearance?

    Hey Guys How much clearance should i have between the bump stop and frame on the lower control arms? Thanks FABO
  9. A

    Wheels! Wheels! Wheels! ( no rallyes)

    Sent pm
  10. A

    Poly Lower Control Arm Bushings VS Rubber

    I agree with Johnny dart
  11. A

    Do I need a snubber on a 8 3/4 rear end?

    Some say snubber is a integral part of your suspension althought I purchased a threaded adjustable one from Mancini looks beefy and cool but i ended up backing it all the way out because I dont want to hear the snubber smashing a hole in the floor every time you launch the car or hit a bump...
  12. A

    4 Speed Pedals 67-76

    Just finished my auto to 4 speed conversion on a 72 Swinger ,Bought a set of pedals off Ebay i belive them to be early A body 66? because the pads are not rectangle they taper inwards like the older style, They fit and function perfectly but i had to adjust the clutch rod nut pretty tight to get...
  14. A

    Fan comes on with wiper washer switch

    hey guys just put my car back together must have mixed up some wires somewhere because the heater fan does not turn on any more, turns on when i wash the windshield any ideas where i went wrong? Thanks FABO:banghead:
  15. A

    How do I get pilot bushing out?

    I used a fine hack saw blade to cut the bushing into two pieces.:violent1:
  16. A

    89 Van starter and alternator

    Hi Guys, Will a starter and altenator from a 89 Dodge Van with 318 work on 72 Dodge Dart 340? Yhanks
  17. A

    over centering spring

    Not to sound like a moron but can you define diaphram style clutch I am not sure about the difference?
  18. A

    over centering spring

    Hey Boys, Just finishing off my auto to 4 speed conversion I have read in some posts that you are supposed to remove the over center spring in the pedal assembley is this correct? Thanks and Merry Christmas
  20. A

    4-15x7 sbp steel wheels brand new

    Will you sell just two?
  21. A

    15"x7" Small bolt Steel wheels Wanted

    Sounds reasonable but i would perfer a set off originals
  22. A

    15"x7" Small bolt Steel wheels Wanted

    Thanks but im really after a set off 15"
  23. A

    15"x7" Small bolt Steel wheels Wanted

    Looking for 2 15x7 Dodge Steel wheels shipping to B.C. Canada. Let me if you have nice ones around? Thanks FABO
  24. A

    WANTED Lower control arms with sway bar tabs

    Sounds reasonable can you send me a picture to [email protected]
  26. A

    WANTED Lower control arms with sway bar tabs

    Will pay good money for a nice set anyone???
  27. A

    WANTED Lower control arms with sway bar tabs

    If any one has a set for an early A body they want to get rid of let me know? Shipping to V9Z-0G5 Sooke B.C. Canada. Thanks FABO
  28. A

    340 vs 360?

    I agree 340s are very cool but i am kind off tempted to use the 360 the throttle response with the fuel injection is impressive there are alot more electronics that acompany this kit but when all is said and done i belive it may be a little more eficient and reliable with less tuning. Having...
  29. A

    340 vs 360?

    The 340 has been sitting in my shop for a while, I listened to it running before it was pulled sounded real healthy has a mild cam, internally stock as far as i know, Motor was freshened up awhile back heads look real clean dont think they have been ported, Guy pulled #s matching drive train to...
  30. A

    340 vs 360?

    Hey guys, Bought a 72 Swinger out off the Yucca Valley a few years ago one elderly owner rust free 318 car, Pulled running gear prepping car for paint rite now. I have two motors and looking for advice and opinions about which one to use... a 1970 340 from a Cuda, X heads, Chrysler Purple cam...
  32. A

    How to remove oil filter plate?

    I will give that a try good idea
  33. A

    How to remove oil filter plate?

    Hey guys, Swithcing to a 90 degree oil filter adapter to clear headers not sure how the original unit which the filter is screwed into is removed? the 1" bolt head is stripped. Any advice on this would be helpful. Thanks
  34. A

    HI-PO Exhaust manifolds or Dougs Headers?

    After many hours of contemplation i have decided to go with the Dougs headers after test fitting them i realized how nice the fit and finish is on them, the only disadvantage is having to play with the zbar to clear not to worried about that. I will be posting this set of 69 HI-Po manifolds at...
  35. A

    HI-PO Exhaust manifolds or Dougs Headers?

    I agree to my knowledge Dougs and TTI,s are the best build quality and fit available for A body's thats why i bought them.
  36. A

    HI-PO Exhaust manifolds or Dougs Headers?

    steering linkage is no big deal
Back
Top