Search results for query: *

well it turns out that i traced the wire from the ignition switch and the privios owner removed the fusible link from the wire and used a wire nut to fasten them together. well the wire nut melted and it shorted out. i put a 40 amp fusible link in it and my accesories now work the engine turns...

ok well none of my accessories work so i t would be a fusible link. ive checked the resistance across the link and i have no resistance. if it was bad it would read an open. that was the one in the engine compartment next to the master cylinder marked with the tab. my service manual says there...

Well I've checked all of the above. And I still have nothing. Can anyone tell me where the fusible links are so I can check them. And I also buy in another ballast resistor on it and that didn't help.

i have about 12.5 volts on the battery. And on both sides of the relay. would the starter turn with a jumper wire if the relay was bad? and i havent checked the grounds but it was running before so i assume they are good but i will check in the morning. does anyone think it could be the fusible...

well i checked it and i think it is good i have power on bith sides and i checked it against a new one at napa and it had the same resistance. Becasuse thats what i thought it was.

I have a 74 duster with a slant 6 of course. I went to start it and it was running really rough. I turn on the light and they came on and flickered then both went out. upon turning it off checking the fuses and battery connections, I went to restart it and i have nothing. no turning over or...

Yep Im a club member. It turned out to be a onr day show cause it kinda got rained out on saturday. it was still a reallly good show looking forward to the Bob Frensley annual show.

It was a bad ground to the ignition box. Another problem solved thanks to FABO!

I have power all the way to the top of the distributor but no spark. I changed the disributor, the cap, the plugs, ballast resistor. I dont know what else to do. Its a 74 duster.

Thamks alot i finally got it on I will post some pics of my slant six/ engine bay restoration soon.

So Ive looked through all the previous posts about this and have failed to find an answer. I have a threaded crank on my 74 225. I rented a harmonic balancer from the local parts dealer and it had a 5/8 threaded bolt that was too small, so i tried the 3/4 and it was too big or the wrong thread...

well i didnt know if they would just raise the front end and call it a day. cause that is what i was told by thr local shop

i recently purchased my second Duster. The previous owner had lowered the front using the torsion bars. I raised it back up a bit to have the stance I like and to help even out the ware on my tires. The way I have it my tires still wear toward the inside. I was wondering if there was a way for...

yeah ive looked at those I think they are kuhmo. that might be what I will have to run for a while untill i can find some other ones.

I have tires on the front of my Duster the size is 165r15 but whenever i call the local tire shop they say they dont have any in that size and they cant get any. I was wondering if this tire is discontinued and if it is what is the closest size to it.

What kind of bracing is needed while replacing the front left and front right floorpans? =P~

thanx for the inputs from everybody, they are greatly appreciated.

Are you mostly doing matal doorpanels or do you do upholstery also?

I was wondering if anybody has pics of custom door panels? I need some ideas. I was thinking about getting the "M" stitched in. inputs?

bump

bump to top

I was just gonna let everyone know about the 14th Annual Chrysler Performance Trade Show and Swap Meet. It's at the Indiana State Fairgrounds in Indianapolis,IN. It is the world's largest indoor Mopar trade show and swap meet. It has over 150,000 square feet of Chrysler cars, parts, and...

I was just gonna let everyone know about the 14th [COLOR=black]Annual Chrysler Performance Trade Show and Swap Meet. It's at the Indiana State Fairgrounds in Indianapolis,IN. It is the world's largest indoor Mopar trade show and swap meet. It has over 150,000 square feet of Chrysler cars, parts...

Im in dickson A about 20 min out of nashville

Hey guys I need help finding a machine shop. I am willing to drive up to two hours for a good one. I live near Nashville. Please leave me the complete name and a number or website.

I have a 74 duster with the front end disc conversion out of a diplomat. i was wondering if there was any way to lower the whole car front and back(leafs) about 2 1/2 inches?