Search results for query: *

Can someone tell me if the upper & lower stainless trim on my standard '71 Duster grille will fit on the OER 340 "sharktooth" reproduction grille? Thanks! Rod in Wi.

I see that Dante's Mopar parts offers a fiberboard 2 piece headliner for '72 & up Dusters.He also sells the plastic replacements.Just wondering if anyone has seen or installed one of these new fiberboard replacements & if so,how is the fit & finish compared to the plastic headliner?

My '72 Duster was built with a 3 speed stick that I replaced with a 4 speed.I also added the reverse light on the dash. My question is where or how did the factory connect the dash light to the harness? Thanks!

I would like to buy a new fuel filler pipe for my '72 Duster but can only find one for '70 / '71 with ECS or '73 / '74 with folding rear seat,or for '75 / '76. Can any of these be made to work on a '72? What changes were made between these years?

I'm looking for help decoding the broadcast sheet for a '66 Valiant 100. It's a 273 Commando/4 speed / 3:91 SG 8 3/4. No radio,heater delete,seat belt delete. There is no factory seam sealer or sound deadener. I'm pretty sure this car was special ordered for drag racing,although it was never...

I am looking for the Mopar part # for the front license plate bracket for my '73 Duster...the parts list I used doesn't show it (or I couldn't find it).My car did have the bracket on it at one time but it went MIA...if I had the part # I could try a search. Thanks! Rod in Wi.

I need a front license plate bracket for a '73 Duster,needs to be rust/pit free.Thanks! Rod in Wi.

I'm looking to buy one 440 emblem like the one pictured,NOS or nice used,must be OEM Mopar. Would also be interested in a pair of "440 FOUR BARREL" emblems.Thanks! Rod in Wi.

Here is a nice 1407 Edelbrock 750,works & looks great,I bought this new,the only thing I ever did to it was to add an electric choke,it is still on the car so if you are local (Neenah,Wi) you can hear it run,just bolt it on & go.$165 shipped in lower 48

Can someone tell me what was originally used to seal between the front fenders & aprons? I seem to recall something that looked like adhesive backed cork stuck on the apron part? If someone has a photo of a car without a fender that shows this stuff that would be very helpful.Thanks!Rod in Wi.

I'm in need of a driver's side tail light lens for my '73 Duster,NOS or really nice used.Thanks! Rod in Wi.

I need some advice on converter choice for my 727.My car is a '67 Coronet,stockish '74 440 HP with a Comp XE262H (218/224 @ .050"),Edelbrock CH4B intake,& an Eddie 750 carb ,2.94 rear with 27.4" dia. tires. Comp says a stock converter will work ok with this cam.I don't have a stock converter but...

I'm looking for dimensions for the output shaft bearing for my '72 727 TF. The bearing that was in the trans has about .001/.002" clearance between the tailshaft housing & the outer race & about the same between the output shaft & the inner race.It is a metric bearing,35 x 72 x 17. Is this the...

Some 727's have drilled & tapped holes on the tailshaft housing for a damper weight but mine doesn't.I would like to add these to my trans so I can mount a damper. Does anyone have a factory drilled & tapped housing they can measure for me? I also need to know the thread size & diameter. I...

Do I want or need these "red" clutches and Kolene steels in my 727? It will go behind a stockish,daily driver, lo-comp. 440 with a 220@050" cam,HP manifolds,750 AFB,2.94 gear. I'm using a Transgo TF2 kit set up in the mild mode and a TCI Breakaway converter ,also have the 3.8 lever. It's time to...

These will fit a B engine in an A body with minor mods (see thread in big block section for photo), they are in nice condition, heat riser spring is bad, casting #'s are 2899879 & 2951216. $300 shipped in lower 48.

1967 273 ci 2 barrel solid lifter V8 with a 904 auto trans from my '67 Dodge Coronet,starts, runs & shifts good,it does use some oil but it doesn't seem to smoke,still in car so you can hear it run & take it down the road.Its been my daily driver all summer & I've driven it from California to...

A set of pistons from a Chrysler Marine 340, look to have little use, for standard 4.040" bore, $35.00 shipped to lower 48, also have a set of rods from a '73 340,motor was virgin, with no spun bearings, good cores but dirty, $40.00 shipped.

3 Mickey Thomson valve covers to fit big blocks,lightly glass beaded,in good shape,missing baffles & grommets,could use a good cleaning,$60.00 shipped to lower 48.

This is from a '70 Sport Fury GT, $100 to your door in the lower 48

Passenger side manifold from a big block Dart,no cracks or repairs,$400 + shipping.

Me & a pal are going to try to drive from LA to Neenah,Wi in a '67 Coronet sedan early next month.We are taking the Amtrack train out there from Milwaukee.We will probably take US hyw 60 most of the way back.Are there any members along this route just encase we would need a a hand? I am sending...

Looking for a pair of NOS tail light lens for a '73 Duster,Thanks! Rod in Wi.

I'm restoring the a/c system on my '73 340 Duster & thinking about converting it to 134a.Does anything need to be changed / modified / updated to the compressor when going to 134a refrigerant ? I understand that the hoses,orings & oil need to be compatible,not sure about the compressor...

Does anyone repop these? I just got my bezels back from the chrome shop,now the lenses look bad & I'd like to replace them.

I'm looking for a pair of NOS tail light lens's for a '73 duster,the part #'s are 3679246 & 3679247.Thanks! Rod in Wi.

I'm looking for one new old stock,original style exhaust tip for my '73 Duster,part # 2883838. Thanks!

I have a complete drum to drum 8 3/4" rear from a '70 340 Swinger,741 case,3.23 open diff,sbp axles,also have the shock mount plates to go with it.The housing is not rusty or pitted. $700,located in Neenah,Wi.

I have a '66 Valiant 100 with an original 4 speed.When I bought the car it had an aftermarket carpet in it.According to the original literature the Valiant 100 came with a rubber floor mat instead of carpet.My big question is has anyone ever SEEN an original '66 4 speed car with a factory...

I have an original heater delete '66 Valiant 100 that is missing the passenger side fresh air vent assy.,the dealer installed a '63 style underdash heater when it was a new car,so the original vent probably got tossed.I am wondering if the RHD cars from down under would use this same part? Can...