Search results for query: *

Vans Auto Ole man Dave

I think its 16 gals. Dave

How do you guys plumb, and wire your Mighty Mite pumps in with your stock mech pumps,???. Do you plumb it into the main fuel line in series,??. Thanks Dave

It will be fine if that cap is rated for gasoline, otherwise it might break down and leek later.

Does the carb have the big flat heat shield between the carb and manifold like in these pics. If not I would make one from aluminum sheet, and install. Or you could put a want add in the parts wanted forum, for one. I don't have an extra. Also note how my gas line is routed, it is made from the...

Fragola is good stuff. I believe its available thru Jegs, and May be Summit. I have bought it thru summit. Dave

Thanks for all the replies. Will go with a Street Demon when the time comes. Might have to figure out if i should go with 625 CFM, or 750 CFM. Dave

Anyone have any experience, or have any knowledge of the new "Street Demon" carbs since the Holley take over of the brand, ??. I am thinking of going with a 625 CFM Street Demon, on my up comming LA 360 build. I havn't found much comment on them being used on SB mopars. The comments are for the...

I would check Summit, or Jegs, and try and match the GPM rating of your pump. They have lots of inline filters with replaceable elements. Dave

Lee R. is correct. 64-5-6 A bodies used one strap from side to side. 67 did also but the 67 straps wont fit (to long). Check your frame rails underneath, you should be able to see where the "T" on the strap fits in the rail. Opposite that is where the "J" hook goes. You need "one strap" for an...

Go to a good Bicycle Shop(where they still fix bikes). By yourself a set of "Park Tool Cable Cutters". If no bike shop, you can probably get them on line, looking up Bicycle tools. They will cut cables clean as you can imagine. Then get yourself a few cable end ferrules, clamp them on your...

Use a drill bit no bigger that 1/8th in for the stop drill hole. I don't think J-B Weld will hold up either. Gas will continue to leach out after J-B Weld is applied thru the crack, and getting under the J-B Weld. Welding is better, or a new tank. Dave

I just received my new 5/16 sending unit I ordered thru Jegs. It was drop shipped from the distributor in Texas. It Jegs PN189-GT09-661S. It is not Chineseum. It's made in Tiawan. I did on "ohms test" on it, and this is what the readings say. L (full tank) 8.2 Ohms...

Been there done that in a similar situation. Glad you found it. Dave

What side of your car is the filler tube on,???. That might make a difference. All the tanks sold here in the states, the filler tube is on the left side. So, if your filler tube is, also, then they are not hard to find. Check out 'Vansauto.com" Just out of curiosity, what side of the road do...

I don't think teflon tape likes gasoline. It might start leaking soon. Get some sealer for fuel lines, an fittings.

I have used "Vasiline" petroleum jelly also, worked for me.

When you drop the tank ( all fire hazard saftey precautions taken), if there is an old tar paper pad there, use it for a template. I made a new one from rubber floor matting from the local hardware store. The floor matting will take up abaision and chaffing noise as stated above. It will also...

I have 2 of the same air-cleaners,for my 67 B-Cuda coupe. They both have the Commando decals on them. Are you in Cali ??, Mine do not have the fitting on them for the hose to the oil filler cap. They are like Cavemans. Maybe the hose is early polution control,from Cali. I thought that did not...

Cave man Ultra seal are good gaskets.you should be fine. Nice Engine. Dave C.

Just got my 340 in the 69 Cuda this week end. Can't find any thing to hitch up the throttle cable and kickdown linkage properly, to the carb. Any one have any experience hitching Demons up. I'ts a 650 Speed Demon on an LD-340 Eddie manifold.I'm still using the stock mopar throttle cable...