Search results for query: *

I need some info on this ! I picked up a 71 Swinger parts car the other day. It has an 8 1/4 in it. Guy told me it is a 3.23 suregrip. This car is a total hack job. Just wondering what years had this rear end and what it should measure to be from an A Body. Thanks in advance.

Can anyone tell me if an LA 727 will fit and work on a Magnum engine ?

Can anyone tell me where I can find a chart to ID what a trans came out of /year/ model car. I have a couple I need to ID. Thanks in advance !

Supposed to be from an 83 dodge van. /6 4 spd overdrive. Looks like 3 different trans bolt patterns on it. The flywheel and clutch came with it. Would this work in an A body ? Thanks for any info. AL

I have this converter that came in my parts pic. Wasn't in a box, and don't see anything to identify it. . I'd like to know if this is internal balance or not. And if it makes a difference if big block or small block. Thanks in advance. Al

My son lives up in MO. and has a cuda. was a drag car decided to turn it back into a street car. I was up there last OCT to rebuild the engine, if anyone remembers that little bit of drama. LOL Anyway he put a spare trans in it then . 904, with MRVB. He texted me today he blew it out while...

Can anyone me what year trans this is ? And how, which #s tell you the year. Thanks AL

Does anyone know the width hub to hub on a Dodge Magnum, like 200? how close to an A Body it is.

I picked up a 904 awhile back, the guy said was out of a 78 or 79 aspen. I posted the # on the pan rail which is 1 PK2892027 2292 0000. A member here says its a 68 according to his book. So when I look up a kit on Ebay they offer kits that fit 62 -65 and another from 66 -92. Looks...

I have a 904 that I want to freshen up but need to figure out what year it is before I buy a kit. The guy I got it from couldn't remember . The # on the case on the pan rail is ( the first letter I can't make out for sure) 1(?)- PK2892027 2292 0000 Has a big 871-2 cast in the bell...

After a hundred miles or so on the Van with a 904 swapped in, I have noticed a chatter in it on pulling away from a stop. Once I get moving the chatter stops. It's almost like on a manual chatter when you let the clutch out . The dash and steering column rattle and shake a little bit. I swapped...

Installed a 904 in and it has a leak at the speedo cable nut. Pulled the speedo gear housing and gear and must be leaking at the seal in the housing where the stem of the gear rides.. Is that seal available anywhere and who might I check with. I don't remember if they come in the rebuild...

Just swapped a /6 904 auto in my A100 Van in place of the manual and need some tips on setting the adjustment on the kickdown linkage. It's just the single rod from the throttle pressure lever on the trans up to the carb . It only has one adjustable slider at the carb, with a pull spring to...

Has anyone seen one of the mini spool set up for an 8 3/4 lately. used to sell them, can't find them anymore . ????? The ones that have blocks that replace the spider gears. If you know where to find some please let me know. Thanks

Anyone know what clutch assembly will fit my A100 Van, /6 ,3 spd. As in what size is the disk and pressure plate? Thanks for any info .

I have a 67 slant6 crank shaft for the small snout converter. I have 2 904s, one is a 67 ( I don't know how good this one is) and I have a pretty fresh 904 1970 with a larger dia. snout. My question is will the 67 converter swap into the 70 904 ( fit the input shaft splines and pump properly? )...