Search results for query: *

I pinched the rear rubber on my oil pan gasket and found Milodon has a one piece rubber gasket.Have any of you guys used this and silicone or no silicone? Should I torque it to factory specs?

Ok so I finally got my heads back and have a few questions.The rocker shafts have a notch in them,does that go to front or rear?What order from front of engine to rear on each side do the rockers go? I kept them in order when I cleaned them but the pushrods looked to be in weird angles so need...

I put Arp main bolts in my 360 and the oil pump does not clear the bolts on the rear cap,I removed the washer and retorqued it and it still does't clear.Have any of you ran into this?,it is a Melling HV pump.

I bought a set of ARP main bolts for my 360 the instructions say follow vehicle manufactures specs torque in 3 even steps to 100 ft lbs but the factory spec on the mains is 85 ft lbs.So 85 or 100?

My 360 does not have the bolt with the hole in it for oiling the timing chain,can a guy just leave the bolt out and run with two? no one in my area has it and said no longer able to order!

I finally got my block,crank,rods,pistons,bearings and rings from the machine shop 3 weeks after he said it would be done! I set the crank in and put on the plastigage,torqued down the main caps and measured the clearance,he turned the crank so I expected good measurements but this is what I got...

I have done a search and read several posts on head gaskets and I think I am more confused now! I am putting together a 360 with stock dish pistons,596 heads with bowl blend and gasket match,Performer int. and carb,and this cam http://www.summitracing.com/parts/crn-693901.The cam according to...

I am looking at the MRG 1121G,so I was wondering if you use a thinner head gasket what about the intake seal?

Are the Mopar head gaskets P4120093 any good or are the Felpro Permatorque the way to go? Looking for something on the thinner side with a hole close to the actual bore size.

I know this isn't an A-Body but I am nglooking for a good cam for my Dodge chassis Rv. It is a 75 360 stock compression,performer intake and carb,planning on dual exh and the heads are 596's getting a bowl blend and gasket match.I have a summit 6900 new in the box,summit's site says this cam...

Buoght a 73 Scamp today now I am trying to figure out what I got.The motor is a 360 and the numbers stamped below the head are 8w3601t6061 can anyone tell me what it is?

Just looking for opinions on a good factory head for a 360 build.A good starting point

I am looking at a 360 from a motorhome the casting # is 4006830-360-8 I have been searching online for info but haven't found much.What I would like to know is aside from pulling the pan is there a way to know if a block is 4bolt main or 2 bolt? I have heard that 2 bolts are actually stronger so...

Going to look at a Ramcharger today,friend of mine told me about it.He does not know fore sure what year or motor but smallblock and early 70's.Motor has aftermarket int and carb,says body is sad but price is right,going to use motor and part the rest if I get it.Question is where exactly do you...

I am planning on a 360 for the 69 dart,just been kind of collecting parts waiting for it to cool down for the work.Swap meet this month so I thought I would look for parts,what are the best heads to look for?I am still looking for body parts too

Guy I bought my disc brake set-up from has a 318 4bbl he says is a cop car motor numbers stamped in it are 4104230 in his book of numbers it shows as 318 race motor.I haven't had any luck searching the web for info.Any of you guys seen this before? I did find one site that listed numbers and all...