'69 Barracuda T56 swap, floor, cross member

-
Had to use compound to get over spray off of paint. A lot of dirt grime came off paint too. Steel wool to get over spray off bumpers. Can't tell it went through floor replacement now.

Plan to drive it an hour away for large local show today. I think its all good mechanically.

PXL_20240524_105050241.jpg
 
Last edited:
Put these out at car shows because a lot of ppl do not know what year car is etc...

PXL_20240524_134611541.jpg
 
About an hour drive each way, several hundred cars at show, made the trip fine. Brake pedal feels more mushy then it should like brakes need more thorough bleeding. But otherwise car ran good. A lot of 5'th and 6'th gear driving at speed low RPMs engine stays nice and cool. Over drive gears so nice on the road trips. Barked tires when I shifted to second and third when I left show light throttle.

PXL_20240524_171045114.jpg


PXL_20240524_211419280.jpg
 
Modifying an extra '69 and earlier AC bracket to mount Sanden compressor. Goal is to use the front third grove in crank pulley as original AC belt did. Also use original AC idler pulley setup.

Rear support bracket is custom and mounts to a longer water pump to timing cover bolt.

Original numbers matching 340 is used for mock up so I don't have to lean over fender of car etc.

PXL_20240603_171349865.jpg


PXL_20240603_171336798.jpg


PXL_20240603_171722249.jpg


PXL_20240603_171436610.jpg
 
Installed on engine in car to check belt alignment. I still had the AC belt back when original compressor was on car in 1982 and it fits.

PXL_20240606_150120376.jpg
 
Custom condenser to filter drier hard line. Hard line from filter drier to firewall is original to the car.

Some guy on this forum used same condenser and custom hard line on a bronze '69 318 fastback. So I stole all the info from his build and copied it.

PXL_20240610_001203543.jpg


PXL_20240610_000933705.jpg
 
Condenser and Compressor installed AC lines mocked up. Hoping for cold AC in another week or so....

PXL_20240615_020543495.MP.jpg


PXL_20240614_132329491.jpg


PXL_20240615_020533295.jpg
 
Mounted PS cooler on its own brackets down low so it gets a bunch of air on it as I drive. Pulled car outside washed it wiped down engine compartment.

PXL_20240615_143837729.jpg


PXL_20240615_144139017.jpg


PXL_20240615_155422832.jpg
 
Cut the suction and pressure hoses to size, crimped the hose ends on, and test fit hoses.

Tweaked shape of liquid line on inner fender so that the two P Clamps line up with the two original phillips screws that were left there for decades to hold liquid line in place.

Key in run position verified 12 volts to compressor clutch when AC dash button in AC mode.

Inching closer to working AC. Need to paint old surface rust liquid line etc but looking to charge / test AC here shortly...

PXL_20240616_235409388.jpg


PXL_20240616_234430957.MP.jpg


PXL_20240616_232441186.jpg


PXL_20240615_181631234.MP.jpg


PXL_20240616_235534112.jpg


PXL_20240616_234422134.jpg


PXL_20240616_233333736.jpg


PXL_20240615_181615987.jpg
 
Last edited:
Fittings at compressor painted black. Liquid hard lines sanded/wire brush surface rust off, flushed, cleaned then painted aluminum.

PXL_20240617_151824084.MP.jpg


PXL_20240617_151853022.jpg


PXL_20240617_151837066.jpg
 
Installed AC lines and vacuumed it down. It held vacuum for an hour so charged it with one can and it holds pressure for hours so far. I have what looks like a failed alternator so decided wait for new alternator before running car. So thats where I left it.

PXL_20240619_232916943.jpg


PXL_20240619_232859024.MP.jpg


PXL_20240619_232836241.jpg
 
Got car up and running with working AC. Video taken after a 45 minute drive in the hot weather:

 
-
Back
Top