[WANTED] Doug’s D453 Ceramic Headers

-
Evan Dutch

Evan Dutch

Well-Known Member
Joined
May 11, 2016
Messages
862
Reaction score
302
Location
North Carolina
Rating - 100%
5   0   0
Contact seller
Kind of a longshot. But, I’m looking for a pair of Doug’s D453 ceramic coated headers. Looking to see if I can buy a set off hand or slightly used to try and save some cash as they are about $1k new. I’m located in monroe NC, will drive a little bit to pick them up as shipping would more than likely cost a decent amount.
 
Evan Dutch said:
would you happen to have a link? I couldn’t seem to find it
Click to expand...
Check Autozone.com to see if it shows up for you. They currently have their 20% off ship to home orders. That ends up being about $181 off a brand new set. If you don't see it, put add them to your art to purchase and use code FALL2024 and see if it works. I can see it when I look right now.
 
Bobzilla said:
Check Autozone.com to see if it shows up for you. They currently have their 20% off ship to home orders. That ends up being about $181 off a brand new set. If you don't see it, put add them to your art to purchase and use code FALL2024 and see if it works. I can see it when I look right now.
Click to expand...
Tried this earlier. The headers are excluded from the discount which sucks because this method used to work in the past :(
 
1730153498488.jpeg

@Car Nut originally posted this and said that it was on the Summit Racing site. Good luck!
 
Evan.....I don't know if @MICHAEL A SCUDDER ever sold his D453's or not? He is in Greensboro. He had the headers at Rockingham last year, and they are NICE. Good luck in your search.
www.forabodiesonly.com

[FOR SALE] - Jet-Hot Coated Small Block Doug's D453 Headers.

*NEW. NEVER RUN. MOCKED UP IS ALL.* I bought these Doug's D453 1-5/8" headers in raw steel new and took them to Jet-Hot in Whitsett,NC. The were then sent to Jet-Hot in Oklahoma. They have their Extreme 2000° black coating on them. Absolutely tough and heat resistant. Hard textured black...
www.forabodiesonly.com www.forabodiesonly.com
 
Evan Dutch said:
Tried this earlier. The headers are excluded from the discount which sucks because this method used to work in the past :(
Click to expand...
Darn it. That was a good way to get them before.

Someone mentioned the $100 rebate. I just checked Summit and they are in stock and the rebate info is listed there. You could probably use a ten percent coupon from Summit, free shipping, and then also get the rebate back on them. That is something like $760 to your door, brand new, after coupon and rebate.
Also, just to make sure you know, they do have a stainless version now.
 
Bobzilla said:
Darn it. That was a good way to get them before.

Someone mentioned the $100 rebate. I just checked Summit and they are in stock and the rebate info is listed there. You could probably use a ten percent coupon from Summit, free shipping, and then also get the rebate back on them. That is something like $760 to your door, brand new, after coupon and rebate.
Also, just to make sure you know, they do have a stainless version now.
Click to expand...
I called summit/jegs. The cheapest they’d do is $900 shipped. And after the rebate it would be $800. I saw the stainless ones, I’m thinking of going with the ceramic ones since they’ll put off less heat in my engine bay
 
Evan Dutch said:
I called summit/jegs. The cheapest they’d do is $900 shipped. And after the rebate it would be $800. I saw the stainless ones, I’m thinking of going with the ceramic ones since they’ll put off less heat in my engine bay
Click to expand...
Right. But use a Summit coupon for ten percent off. That makes it $809 shipped, plus tax. I have a coupon I can give you. And @GTX JOHN may still have the coupons too.
Summit 10% Discount Coupon Available Again!
 
Big.J.007 said:
Be ready to grab your ankles... I reached out to Michael on them, and he wanted $950 shipped..
Click to expand...
Headers were $450 raw and the Jet Hot coating was $850 so selling them $950 shipped makes me the one grabbing my ankles. By all means by the $700 set from summit with a painted on coating that will chip off and is no where near rated for 2000°. This same coating was used on a set of C6 ZR1 headers and you could lay your bare hands on the tubes 10-15 minutes after a Dyno pull.
 
JDMopar said:
Evan.....I don't know if @MICHAEL A SCUDDER ever sold his D453's or not? He is in Greensboro. He had the headers at Rockingham last year, and they are NICE. Good luck in your search.
[/URL]
Click to expand...
Thank you for the mention. Still have them. They are very nice. Coated on both sides. 2000° black textured extreme on the outside, standard 1300° on the inside. No header manufacturer's std coating is rated for that.
 
You must log in or register to reply here.
-

Back
Top