Nope nope nope.
Clearly a scam. Or,too much money for junk. Paypal friends and family, means just that.
Clearly a scam. Or,too much money for junk. Paypal friends and family, means just that.
Is this a crack
- Thread starter SnowDrifter
- Start date
-
attenuated
Attenuated
Lakewood is making bell housings "new" for gen 3 Hemis as well as small blocks that accommodate a883, tremec trans. Sold through Holley. Good luck, hope this helps.
SnowDrifter
Well-Known Member
Are you saying the a883 is the same transmission as transmission as the chevy TKS 600
attenuated
Attenuated
One of the mopar mags had some information on the Lakewood bell housings sold through Holley. Go to the Holley wesite and search for Lakewood bell housing for the current information .
famous bob
mopar misfit
not enough shown to make a statement !
j par
Well-hung Member
If this thread was started by @pittsburghracer I would have never opened it...
69_340_GTS
Well-Known Member
One clue ought to be the pentastar and Mopar part number cast into it. You know, they never manufactured anything like that. As far as I know.
SnowDrifter
Well-Known Member
I've done a lot of things surprise I'm still alive Never did the crack don't like no cracks
Ordered all new
You wont regret it.
SnowDrifter
Well-Known Member
I bought the 71 Datson in 1975. Been on and off the road ever since. In high school they said can't put that mopar in there they're too big.
So the other day I was Kayaking across the lake. The engineer, legend kayak Builder Racer, Auto Racer says the 413 is heavy!!!
I said
I don't think so, see you at the race. So I thought I needed more power and got the 440
So the other day I was Kayaking across the lake. The engineer, legend kayak Builder Racer, Auto Racer says the 413 is heavy!!!
I said
I don't think so, see you at the race. So I thought I needed more power and got the 440
SnowDrifter
Well-Known Member
And the motors even blue
65wgn440
Well-Known Member
Man, if you couldn't tell that was a scam in three seconds, you better stop buying stuff on the internet.
mcodecuda
Senior Member
That’s a race motor for sure since it looks like it was
Balanced and Blue Painted.
SnowDrifter
Well-Known Member
SnowDrifter
Well-Known Member
It's easy to see it was blue painted.
I know it's very well balanced I went up The mountain and down the other side from Lake Tahoe all 2 lane
The motor never fell over once
I know it's very well balanced I went up The mountain and down the other side from Lake Tahoe all 2 lane
The motor never fell over once
AJ/FormS
68 Formua-S fastback clone 367/A833/GVod/3.55s
- Joined
- Jan 19, 2014
- Messages
- 25,992
- Reaction score
- 13,297
The 440 can't hardly fall over;
she has a ton of bottom-end, and usually, short legs....
Kindof like my neighbors wi
Dale Davies
Well-Known Member
NO, that is a crack. Is it aluminium? Basically unless it is a rare collectible part, it is worth scrap weight. Could it be repaired it aluminium? Yes but at what cost? You would have to press the trans face to close up the gap, grind out or groove the crack and weld it. Then alignment would need to be checked. Probably not worth the trouble and better to walk away.
Dale Davies
Well-Known Member
Pushing to make a rush decision? That is a bad crack. Run and hide, send no money. That bell hsg is only worth scrape price.
Dale Davies
Well-Known Member
Are you saying it is constipated?That is a crack, but looks a bit stopped up.
Bret Tschacher
Well-Known Member
If it's an alloy housing it can be repaired and be about as safe as OEM, which isn't saying much. If it were mine, I would repair it and make some reinforcement pieces for it, both sides, and use it. As long as it wasn't for any super high powered project. I had a buddy in HS. owned a 68 RR that was pretty much totaled on account of housing failure one night. Took out the floor, all the way back to the rear axle being tweaked beyond use, leaf springs and mounts too. Personally not a big fan of any housing that isn't made from stamped steel and even then, prefer to have a mid support of some kind.
-
