I am in central massachusetts, i have a 73 dodge dart that i bought for the engine and transmission and brakes (v8 swap). The car is not great, but does have some good parts on it if you need them. The front fenders are in ok shape, some rust on the bottom but i have seen worse and there are some dents, useable if you have the time. The doors are in good shape, some minor lip rust on the inside but otherwise good with glass. Interior is shot, quarters are shot. The rear valance appears to be in good overall shape, some small dents and some rust. steel wheels. hood and trunk lid are there, some rust but also appear useable. Not looking for much, if you can remove it much cheaper.
parting 73 dart
- Thread starter redfivexw
- Start date
-
- Status
73SwingerBuild
Well-Known Member
Is it a 73 Swinger? 2- or 4-door?
I'm in North Smithfield, RI. If the interior is black (or even somewhat usable), I could use some odds and ends off of it. What is left on it?
Any pics you have would be pretty helpful.
Thanks.
-Mike
I'm in North Smithfield, RI. If the interior is black (or even somewhat usable), I could use some odds and ends off of it. What is left on it?
Any pics you have would be pretty helpful.
Thanks.
-Mike
it is a 2 door swinger. The interior is white, sorry. I dont have any pics right now, but like i said, the fenders have small rot holes in the very bottom, could be patched very easily and each one has a small dent near the front. The doors have no dents or rust holes, just minor lip rust on the inside underside. The trunk lid is dent free, i see a bit of rust on it, could be fixed but these usually dont rust. The rear taillight area is complete with all lights/bumper/valance, would be good for somone who wanted to change their 74-up rear end. Quarters are shot. interior is complete but has been exposed to weather and is terrible. Side glass is all there. Hood is good, front bumper is junk, inner fenders look good, but i may be cutting those out for myself. Radiator support looks good.
73SwingerBuild
Well-Known Member
Whereabouts in MA are you? If it's not too far a drive, I may want to come check it out to see if there's any parts that I could use off of it.
GeorgeGerhard
Well-Known Member
I would like to but the A pilar mouldings if you have them
lilhows340
Well-Known Member
I could use the seat belts if they're black.
driver side door looks good, no dents, some lip rust. Sandblast and should be good to go. $50 complete if you take it off and pick it up, $100 if you want me to take it off and bring it to greyhound (50 miles round trip for me) plus the ship charge.
RedFish
Well-Known Member
- Joined
- Sep 5, 2007
- Messages
- 25,849
- Reaction score
- 5,359
I was hoping for a slotted bezel with a lever that moves up/down and possibly the linkage, etc.. inside the seat. I'm not sure what year they changed.
I dont know of push buttons will work for my bucket seats without having all the linkage, latches, everything, and pictures of how it installs and operates.
Dodge33
Well-Known Member
What's the condition of the upper inside door plastic that run's
the length of the door? How about the inside door handle plastic cup's?
Maybe the inside door handle's too? Would like the screw's with them also.
Thank's
the length of the door? How about the inside door handle plastic cup's?
Maybe the inside door handle's too? Would like the screw's with them also.
Thank's
7dart0
Well-Known Member
im in mass also. i could use steering column, heater box cover, glove compartment whole thing with liner, rear seat top half. was the vehicle manual or power steering? if manual how much for box? maybe front seat and dash pad.
let me know thanks. tom
let me know thanks. tom
- Status
-
