Stop in for a cup of coffee

-
Morning to you all. Yet another hot day here again the guess is for 103.
One last hot day tomorrow and then we return to more seasonal temps....I'm ready!!
I'm going out early again and finish the painting project I've been working on the past few days.
 
Morning to you all. Yet another hot day here again the guess is for 103.
One last hot day tomorrow and then we return to more seasonal temps....I'm ready!!
I'm going out early again and finish the painting project I've been working on the past few days.

Definitely good to get outdoor stuff done early.

My brother's work has been sending staff home early. 18th century mill...so there's no real climate control going on.
 
Last night the weather guesser said in the last six weeks we'd had 32 days in the 90's and 10 days over 100.
It is summer...but I still don't like it.
 
Still unpacking and doing a few rush distributors for people. Need to et some one over here before putting the distributors away to do a inventory to see what I actually have. Takes forever one deep.
 
4160 Holley....

But I'll still talk to you :D:poke:

You're just ahead of me. Coolant hoses are set for replacement this weekend
I have a Holley Avenger 670 cfm waiting in a box, this 650 Eddy is my start up carb to get everything spinning, water and trans fluid is next in line, just need hose clamps
 
I have a Holley Avenger 670 cfm waiting in a box, this 650 Eddy is my start up carb to get everything spinning, water and trans fluid is next in line, just need hose clamps

Thought about new versus rebuilding... but the carb was installed in 2012 and only has about 4,000 miles of drive on it. Unsure what toll all the time sitting took but I'll find out I suppose
 
Same here 1806 Edlebrock. Kit, should/could be here today.
I ordered a cheap amazon kit. Wrong. However it works with a different carter carb. Which needed new metering rods.
So i think i will order the proper eddy kit.
 
My Mopar buddy John from Maryland is coming out for a few days in September.
We get together at least once a year if not more.
We are like brothers from another mother and have a great time together.
He always buys an open-ended flight when he comes.
Last time he was here about three weeks but who's keeping track when Cheryl asked when he was going home...oh ok.
This time she made his reservation, and we already know he's only here 10 days...:(
I've warned him too that now she's home every day now and we'll have to be on our best behavior. :rolleyes:
 
I ordered a cheap amazon kit. Wrong. However it works with a different carter carb. Which needed new metering rods.
So i think i will order the proper eddy kit.
I did the same, mainly to get the gaskets needed to open it up and clean, set floats . Hope it's all it needs.
 
Whatever kit you guys get make sure it is ethanol compatable (needles and seats, accell pump). Carb junkies has them if needed.
 
I ordered a cheap amazon kit. Wrong. However it works with a different carter carb. Which needed new metering rods.
So i think i will order the proper eddy kit.

Ordered the Holley kit from Summit.... they ship faster than getting it direct from Holley.

Still need to figure out what the timing is set to and what are a good set of jets to go with.
 
My Mopar buddy John from Maryland is coming out for a few days in September.
We get together at least once a year if not more.
We are like brothers from another mother and have a great time together.
He always buys an open-ended flight when he comes.
Last time he was here about three weeks but who's keeping track when Cheryl asked when he was going home...oh ok.
This time she made his reservation, and we already know he's only here 10 days...:(
I've warned him too that now she's home every day now and we'll have to be on our best behavior. :rolleyes:
You two on best behavior? That just funny right there. I give ya three days before Cheryl throttles one, or both of ya! Hah! Hug him for me and tell him is said hello!
 
Good Morning All! Another work week down, time to relax. Jet City rentals is dropping off a KX-80 excavator today, will have for the weekend for some stump removals up front.
 
Still unpacking and doing a few rush distributors for people. Need to et some one over here before putting the distributors away to do a inventory to see what I actually have. Takes forever one deep.

Hey Ray, how did you do there this year?
 
Good Morning everyone. I hope all is well. Backread is done. More computer work, but a little shorter of a day. My boy came over last night, tried a ethnic mix dinner. Korean style sautéed mushrooms over Spätzle. Turned out very good.

upload_2022-7-22_7-15-4.png
 
-
Back
Top