zkx14
Duster De-ruster
stuff is all out and sign is up. More coffee and wait...
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
Thats the other side!
FISHYPETE
Well-Known Member
The two I have measure 16“1/2 X 12”
zkx14
Duster De-ruster
zkx14
Duster De-ruster
Now those need alignment often I bet!
Yup, really close to the drain….
Dang its cold. Im really not looking forward to whats coming in the next few days. That reminds me, i need to get gas for plow truck.
The older I get the less I like winter. I hope to be a snow bird in a few years.
zkx14
Duster De-ruster
You may not want to hear this then... Almost 70F right now.
65 here , enjoy !
Thank you very much that helps a lot.
Thanks Pete I'll be welding up the brackets to hold the seats today.
Good morning c\_/ folks. Wife and I went fishing at Lake Hartwell yesterday. Had a great day too. I called my brother to tell him about it. He said that lake was over its normal banks when he took his camper there 1st week in May. Yesterday we had a muddy, rocky, way to walk all the way around the cove at Boyles Landing. Water is 50 to 60 yards away from normal bank. Over there is where the bigger Bream are. We got them until we ran out of worms. Loaded up all of our stuff and walked back to the car shortly after 5PM. We had 3 inches of red mud caked on the bottom of our shoes. I stumbled countless times but never actually fell down. My brother said, "I kind of want to chew your *** out. You know how fragile you are. What if you had fell? But hey, you could only dream about fishing through May and June so I'm glad you had a great day. Not everyone gets a 75-degree day to do anything in early Nov".
Got the load of dodge parts out of my trailer. And picked up 4800 lbs of pellets. Another 2400 to go fetch later
zkx14
Duster De-ruster
Slow day at yard sale. I am getting somecleaning done in the garage though. I moved half the sale stuff to one side and put up a big free stuff sign like half hour ago. Nobody stopped since I did that. 
So got the holder for the bar stools done today and just need the seats and swivels for the stools than can paint the rest up and start on the bar part next.
All the pellets are stowed away. Dumped oil in forklift. On floor mostly. It pours out onto crossmember. Stupid. And what a mess. Am i wrong to think it gets milky due to propane? Tempted to try and adapt a carb and run it on gasoline.
Toad drowning.Dad always called it a "frog strangler". I wonder which is worse?
Frog parking only...
All others will be toad...
zkx14
Duster De-ruster
Hartwell? You from that area? I have family in Clemson and Aiken.
dukeboy440
Well-Known Member
Good evening.
Well I’m still fighting this quarter panel. It’s almost like the center body line isn’t defined enough. Which makes sense cause the bottom had to be pushed up just to get it this close and to make contact with the rockers. On the drive home, i came up with an idea. I’m gonna measure the distance between the inside of the quarter at that line and then repeat on the drivers side, which is aligned perfectly.
Well I’m still fighting this quarter panel. It’s almost like the center body line isn’t defined enough. Which makes sense cause the bottom had to be pushed up just to get it this close and to make contact with the rockers. On the drive home, i came up with an idea. I’m gonna measure the distance between the inside of the quarter at that line and then repeat on the drivers side, which is aligned perfectly.
Looking at the door edge in the picture it looks a bit to thick to be factory and if it's full of bondo that would account for part of the problem I would think.
-
