See if they will ship it?
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
Gonna hopefully put my center section back together tonight and put it back in noisy.. and see if i get sick of the 4.57s or not before i buy new gears... with how little power i will make i hate to go down to 3.91s or lower (numerically) but will see how it goes.. need more miles first.
Put two together it is dangerous!
mopar 8/34 rebuild kit
Mopar 8 3/4 clutch type rebuild kit new old stock $75 Will not answer to is this still available will delete when sold
www.facebook.com
This is an insanely good deal for you SPB guys...
www.facebook.com
SBP Mopar 15” Polished Wheels with/ New Hankook Tires
Tires are brand new with Stickers still… wheels are very nice used wheels with a new set of center caps. 15x6 fronts with 3.75” backspacing (+6mm offset) with 205/65R15. 15x7 rears with 4”...
www.facebook.com
Morning!
Just below freezing, expecting sun today though. Will go on a quest for a fuel pump that i know i have somewhere on the property. Then clear out the junk i squirreled awat in the dart.
I got the brakes working, unstuck the calipers by pulling the pads and pumping the brake to force piston out, took out the seal and boot and a light hone.i will be ordering kits instead of new calipers.
Then bleed rears,what a task, climb ladder and block pedal, go down and open bleeder. Rinse and repeat.
Just below freezing, expecting sun today though. Will go on a quest for a fuel pump that i know i have somewhere on the property. Then clear out the junk i squirreled awat in the dart.
I got the brakes working, unstuck the calipers by pulling the pads and pumping the brake to force piston out, took out the seal and boot and a light hone.i will be ordering kits instead of new calipers.
Then bleed rears,what a task, climb ladder and block pedal, go down and open bleeder. Rinse and repeat.
Good Morning world of Mopar misfits! and red heads
You? A red head? Yikes
Well the springs and clips I had made up are trickling in. Got the cam lock rings in, They are unobtainable new. NOT ANY MORE!
Good Morning All! Windstorm here, generator on/off last night. Too many parts in one of those Ray, I'd have extras
We believe you Ray!! : (I will prove it next time I see you where I am not grey!
They always go flying off when taken out. Usually find them stuck on the bottom of my sneakers. Got sick of it. Man not cheap to get made. Setup kills you. Now I am good for future orders. Springs should be here next week. Tell you what I dropped 5k getting these made up.
Yi Yi Yi Yi.....I don't need proof
Cuda Cuda!
I always get asked for them. I am going to hit up some of the larger companies to see if I can get them out in quantity. So far alot of custom stuff being made up for me. Slant HEI plates, Dual point distributor leads, HP advance springs and these clips.
Another drive by for me, have to go to Redmond for Safety Meeting. Yard is a total mess, have a huge branch hanging off our Dish, can't get to it yet. Have a Great Day All!
Cracked or broken plastic pieces or parts?
I don't usually believe what I see on YouTube but this video caught my eye. It may be a great way to fix broken parts. Parts like consoles, gauge bezels, kick panels, and anything else made of plastic. It may also work on fiberglass as well as dash pads. Check it out I would like to try it and...
www.forbbodiesonly.com
I'll have to try this
dukeboy440
Well-Known Member
Yay!! Guess what important day today is and what I’m doing!!!
https://youtu.be/huSjmj3c500?si=RdAaHJc0L_5fojm2
https://youtu.be/huSjmj3c500?si=RdAaHJc0L_5fojm2
dukeboy440
Well-Known Member
You are going to fail at blowing up parliament, get captured, tortured and die a failure that for some reason gets renown as a hero? go Fawkes yourself!
-
