Anyone ever massage the base on one of these nice original cleaners. The other is a Mancini repop made to fit - not as nice but you can shut the hood
UPDATE - Looks so good but ya can't shut the hood
- Thread starter Michael Siple
- Start date
-
70SwingerGuy
Well-Known Member
Given the current value of an original air cleaner, there is no way that I would "massage it" in any way!!
I cannot disagree.
abodyjoe
Well-Known Member
the 70 style doesn't fit under the hood? what carb and intake are you running that it doesn't fit??
no i would not modify that 70 air cleaner. they bring way too much money these days to hack up.
mine fits with a performer rpm (non air gap) and a holley.
no i would not modify that 70 air cleaner. they bring way too much money these days to hack up.
mine fits with a performer rpm (non air gap) and a holley.
That looks like a B Body air cleaner.
You may find some helpful information here. Nick's Garage - Air Cleaner Identification
abodyjoe
Well-Known Member
his top one looks like a 70 340 air cleamer and bottom looks like the 69 style 340 air cleaner.
Now that I am off my phone and on my laptop I can see the difference. THe last one he posted is a unsilenced air cleaner. You can mess with the height on those by trying different base plates. Like you said, the top photos are a 70/71
You didn't mention what car you have here.
Looks like a pretty thick spacer under the carb. You might want to try a little thinner one.
Mopar Momzee
Well-Known Member
Agree looks like a spacer in there . I have a hemi in my charger had to remove the 1” spacers to get hood to close as well.
Something else to mention to members when we recommend an insulator because of fuel boiling issues. Make sure the hood closes.
Mine fits, but it’s close. I run the Edelbrock Performer RPM and a spacer. Edelbrock AVS carburetor.
If it were for my own car, I wouldn't care.
It looks like the unsilenced cleaners fit but the 70-71 doesn't (with a spacer) One thing about the unsilenced version,you can buy a dropped base. THe lid doesn't care what base is under the filter. With the 70-71 unit, the lid and base need to be used together. Just what I see here.
4mulas
Fixem'up
That’s one thick spacer under the carb. Remove that and then try.
Dartswinger70
Well-Known Member
Yup its usually a spacer or the intake is too high issue. Fun snippet of info the Edelbrock Torker while it is not popular for some was a low rise single plane that was designed to fit under a street car hood...
The old LD4B's and LD340's as well.Yup its usually a spacer or the intake is too high issue. Fun snippet of info the Edelbrock Torker while it is not popular for some was a low rise single plane that was designed to fit under a street car hood...
this is a Duster with edelbrock rpm intake with their 800 avs2 & 1/2" heat sink. Don't think I want to mess with the original & live with the one that fits. Don't want to lose the spacer. Now I have a nice air cleaner on the shelf to look at. Thanks folks -Mike
Dartswinger70
Well-Known Member
The 70-71 air cleaner is already pretty flat or low looking IMO. Oh well time for a Super Stock hood right?
6PKRTSE
Well-Known Member
Agreed, I do what I need to or want to on my cars. Hack it up to make it work if you need to.
I did on my air cleaner base on my Roached Runner to clear the taller Edelbrock intake and 2 stage nitrous plate.
Uncle Bob
Shiny paint causes stress.
I just dropped in to say I sure wish someone would start reproducing pie pans again.
AJ/FormS
68 Formua-S fastback clone 367/A833/GVod/3.55s
- Joined
- Jan 19, 2014
- Messages
- 25,834
- Reaction score
- 13,141
I did have a 70 on my 750DP/AirGap. but eventually I cut a hole in my hood and sealed the carb air-horn to the underside.
No spacer in either case.
No spacer in either case.
-
