Search results for query: *

I recently bought a 77 440 that came out of police car. I got it back from the machine shop and I have some questions. It is bored 30 over and the cast crank is ground 10/10. I have the balancer and the converter that came off of it so is it still balanced? If so, do I just have to match the...

Tomorrow I am going to re-install my performer intake on to my 72 318. The Fel-pro gasket kit came with the metal 90041-1 gaskets. I had Fel-pro 1243's on it before. Does the raised side of the metal gasket go against the head or the manifold? What kind of sealant should I use on them? The...

I have a 2 1/2 hour drive home from Carlisle. On the way home my 72 D100 stalled going down hill on the turnpike. I just put it in N and started the 318 back up. An hour later it happened again going down hill on route 56. This time I pulled off the road because it wouldn't fire up while...

I have the SBP 8.75 axles, backing plates, brakes and drums that I took out of my 68 Dart when I switched to BBP. They originally came out of a 72 Duster 340. The splines on one of the axles looks goofy but they worked well in my Dart. I can bring these to Carlisle. $200.

I got my show field sticker today. I am taking my 72 D100 this year and I am in the blue show field B301. I had brought my 68 Dart the last ten years. The A-bodies have been moved to the green show field.

I started my 68 Dart this morning and backed it out of the garage. While pulling it forward to the side of the driveway it just shut off. Now, when I turn the key there is nothing. Tomorrow I will get out my tester and my service manual and try to figure it out. Any advice on where to start will...

I just tore down an old 440. One of the rocker arm supports is broken. Is this head fixable or should I be looking for a replacement?

4006630-440-10 A friend of mine from work wants $400 for this engine. He remembers it coming out of a running police car. What do you think. He wants to know by tomorrow.

I pulled in the garage last nite and noticed a puddle under the car. It was power steering fluid. It was leaking out of the cap. I don't think it was overfilled. Has anyone else had this problem? Any advice? Thanks FABO.

I decided to go fill up the 68 Dart for the trip to Carlisle. I turned the key and it just kept cranking without starting. As soon as I turned the key back to run it started. Anybody ever have this issue? Any advice? Thanks FABO.

I switched to power steering so I have a PST 16 to 1 manual box out of my 68 Dart for sale. It is small sector 1 1/8" and only has about 1000 miles on it. I will sell it for $250 shipped. Thanks FABO.

I have a 3.55 cone style sure grip for sale. I switched to a 3.23. The 3.55 was making a slight humming on acceleration so I put in new carrier bearings after I pulled it. It also has a 1350 pinion yoke and a new pinion seal. I am asking $400.00. It is located in Johnstown, PA. I could bring it...

I need a power steering pressure hose for my 340 that came out of a 72 Duster 340. It came with a Federal pump. There is alot of conflicting info online. I am hoping a FABO member could confirm the correct hose. Thanks.

I think I have a head bolt leaking oil. It is the bottom, rear, passenger side bolt. My oil pressure is always between 65 psi and 75 psi. Does that bolt go thru any oil passages? I could back it out and put a washer and some RTV on it. Any advice will be appreciated. Thanks FABO.

I need a federal pump and pulley for the 72 340 that I put in my 68 Dart. Here is a picture of the parts I need to replace. I gave the old rusty Duster 340 to a member of this site. I think the power steering pump, pulley, and brackets were in the trunk. I never thought I would go back to power...

I have a 68 Dart. My temp gauge just went from working intermediately, to not working at all. The fuel gauge is working. I replaced the circuit board and voltage regulator a year ago. I also have a new temp sensor. When I ground the sensor cap the gauge does nothing. When I test the voltage on...

I put a gauge set in my 68 Dart. The 3/8npt mechanical temp sensor adapter doesn't fit the inlet on my air gap intake. It will fit the inlet on the water neck. Does it matter what side of the thermostat the sensor is on? Can I drill and tap the intake with it on the engine?

I have a 3.55 cone style sure grip I just pulled. It was whining on acceleration. I just put new carrier bearings on it. I put a 1350 pinion yoke and new pinion seal on it last July. I am asking $500.00. It is located in Johnstown, PA. I have a friend who could deliver it to Mopar Nationals next...

I am selling my Harley so I am going to put some money into my 68 Dart. I am taking off the D453 headers and go with exhaust manifolds. My 72 340 was put back to 68 specs. It has 2.02 and 1.88 valves, a forged crank, a cam, and 10.5 to 1 pistons. Will the higher flow 68-70 manifolds bolt right...

While driving home from Carlisle, I noticed the whine from the rear end has got worse. It whines on acceleration. It is a 741 case 3.55 cone style that I bought here on FABO. I have the original open 3.23 741 from a 72 Duster 340. I want to go to 3.23 sure grip. Would you buy a sure grip for the...

I bought a dual exhaust kit from LMC Truck for my 72 D100 318. It is aluminized steel. I hate it and want to modify it. It goes outside the frame, I want it inside the frame. I have an Eastwood MIG. Can the aluminized steel be welded to mild steel bent tubing?

What is this part for? Do I need it? This part is connected to my coil on my 72 D100. It mounts right on the coil bracket.

I just put a 4 barrel intake and carb on my 72 Dodge D100 318. I fired it up to check the timing and to adjust the edelbrock carb. It's an automatic 727. I put in N and pushed it out of the garage and fired it up. It is running in neutral while adjusting the carb. I look down and see a puddle of...

I am putting a four barrel on my 72 D100. I removed the 2 barrel intake and when I dry fitted the 2176 manifold I noticed a void not covered at the exhaust crossover. Is this OK? I didn't notice it when the old intake was on, but it appears it did not cover it either. I think I'm okay. I just...

I have been looking for some Adventurer tailgate trim for a couple years. I looked at Chrysler Nats, Truck Nats, and Mopar Nats with no luck. I clicked on an image and it took me to a four year old post on Ramcharger Central that included a phone number. I sent a text and got lucky. The top...

This weekend is our first trip to Mopar Nats. I'm looking for dinner recommendations for Friday night. What are the best restaurants? Thanks for any tips.

I mailed a registration form and check to Mopar Nats in June. I haven't heard anything back from them. No letter, no emails, no nothing. This will be my first trip out there. Is this normal? Do they send out window stickers like Carlisle? Thanks FABO for any info.

I am changing my pinion yoke and seal because of a leak I noticed after I got back from Carlisle. I ordered a 10 spline yoke, a seal, and a u-joint from Dr Diff. I have a 741 case. I am wondering if I will be able to loosen the nut. Can I get the yoke out without a puller? Should I drain the...

I have two 15x7 SBP Cragars for sale. They are in excellent, almost new condition. I switched my rear to BBP. I am asking $250 plus shipping for the pair. I am in Johnstown, PA 15904. I could deliver them to Chrysler Nationals at Carlisle.

I'm looking for a torque strap for my 68 Dart.