Search results for query: *

yes i know its harder,but im not pulling the engine.i know what comes off,but i need the proper way to install gaskets,seal cork to block ect,ect.i need the sure fire way as im not doing it again.i would even go with the right stuff instead of gaskets if it will work on 360 small block.nor...

do all 360's use a center sump pan?i need a new pan.its going in 73 duster

i stripped the header threads on my edelbrock head.we tried and tried,but finally just removed the helicoil and put a steel bolt with antiseize in.what ill effects will this have in the future?will it back out?or will i not be able to get it out again?i know i should have pulled the head and had...

pass side,chrome needs to be really nice,and glass needs to be tight.will pay for good one

same 408 stroker.built by a very rep.builder.his dyno shows 498 hp.518 tq.the rings did not seal and he did not want to stand behind his work.engine biulder #2,torn engine apart and corrected the problem.his dyno shows 433 hp and 467 tq.wow,why the huge difference?thats 60 hp and 50 tq.both are...

67 & up a body.tqa. lightly used. all hardware included.you know what they look like,if not i can text you photo.$55.00 includes shipping.pm if interested

i worried using a plate with engine alone into aluminum intake. went just fine.how about with engine and trans together?small block&727.same aluminum intake,or should i use chains?aluminum heads.

408 stroker smokes and burns oil at a rate 1qt 500 miles.builder says leakdown was less than 2 %.only thing he could find was less than enough sealant on rocker studs(magnum eddys)he ran it with the pcv unhooked and smoking stopped,told me to get a catch can.i did,very little oil being being...

i have a 408 magnum and want to check valve lash.it has comp magnum roller rockers.its a running engine.do i hand turn crank until its on the base of the cam and tighten while turning pushrods until i feel a slight resistance? then tighten another 1/4-1/2 or full turn?its a hyd.roller cam.i know...

i have spool mounts and a torque strap.is the strap not needed with the spool mounts?if so i can sell someone the schmacher strap that needs it

oneal transmission in clinton,indiana.took my 61 newport in for a rebuild,he told me $1200-when i picked it up it was $2500.00.he charged me $ 500.00 for a stock convertor,140 for a netural saf.switch.i was pissed,but could do nothing.i had nothing in writing,just verbal.never again without...

i have a small block with 10" of vacuum.breather on one side,pcv on the other.my question is under load or full throttle there is little to no vacuum.how does the engine get rid of blow by?would i benefit running a hose from the breather on the valve cover to the base of the air cleaner,so it...

i have 2 lightly used accel super coils.8145 chrome,and 8140 chrome.$20.00 each shipped,or $30.00 for both.pm if interested.

a guy was telling me how he shimmed out his transmission on his 57 chevy.instead of buying the correct spacer,that goes all around the transmission,he used washers on the bolts to shim 1/4". he has restored 4 really nice chevys,so this kind of threw me off.i had to laugh

like new,stock jets and pv,vac.sec.used very little,going to a double pumper.needs nothing.lists for $560.00,will sell for$300 pm if interested, fuel line included.

like new,stock jets and pv,vac.sec.used very little,going to a double pumper.needs nothing.lists for $560.00,will sell for$400.00 obo $20.00 shipping.i can text you pictures if you want.pm if interested

i run a cannister and still have gas fumes.so it came to the charcoal saturated or just plain worn out.i found a gm cannister that was the same size and was able to use orig. bracket.no more fumes.that is awsome.ive fought this for a while now.you all know the feeling you get after trying and...

nice chrome fuel rail with guage.9 3/8 center to center.fit on my holley 3310 ect.ect.can text photo.$20.00 shipped pm if interested

6.5" can text a photo if you want.$20.00 shipped.pm me if interested

i have a nice stock driveshaft with newer balance and newer u joints.has the 7260-7290 rear conversion u joint.complete, painted,ready to run.comes with front yoke for a 727. 45" center to center on the u joints.pm me and ill send you a photo.$150.00 shipped.pm if interested

in unopened package 240-7301.$10.00 includes shipping.pm if you want em

bolted on ,good as new condition.can text you a photo if needed.$20.00 includes shipping.pm if you want it.

NEWER BUSHING INSTALLED.I CAN TEXT YOU A PHOTO IF INTERESTED.$30.00.$10 SHIPPING PM IF INTERESTED

3" ,44 3/4 INCHES LONG.THAT IS CENTER TO CENTER U JOINTS.NO YOKE.I CAN TEXT PICTURE IF INTERESTED.$150.00 SHIPPED.

$20.00 SHIPPED.I CAN TEXT YOU A PHOTO IF NEEDED.PM IF INTERESTED

pull balancer back off and lube it? or not worry about it?

mike built me a 408 magnum stroker.took it out for a drive today for the first time.it dynoed at 498 hp and 512 torque.my 73 duster took a liking to it.not a race car,just a hot street car.mike really knows his mopars,im very impressed with it.12" vac. so i was able to heep my power brakes.runs...

looking for a water pump pulley for a 1973 340 duster,and having a hard time finding one.part #3698924,is 6"dia. x 2 3/4" tall. why is this special?what are my options if i cant find it??

need a small block water pump pulley.single groove,6" dia.x 3" tall.pm if you have one to sell

73 340 duster,26" radiator.clutch is leaking the fluid(silicone) but still has resistance when spinning it.im quessing its on its way out.anyone know the hayden part# for the clutch??