Search results for query: *

Thanks FABO. I ordered some 1243's.

Tomorrow I am going to re-install my performer intake on to my 72 318. The Fel-pro gasket kit came with the metal 90041-1 gaskets. I had Fel-pro 1243's on it before. Does the raised side of the metal gasket go against the head or the manifold? What kind of sealant should I use on them? The...

I replaced the condensor and started it. It made the same knocking sound. The inside of the cap looks ok to me. A toasted rotor could cause it to knock like that? It fired right up and ran. There is nothing hanging from the coil, that is a ridge on the 4 barrel intake.

I pulled the engine and tranny out. I got service paperwork when I bought the truck. The tranny was rebuilt by aamco in 2008 at 45,000 miles. The truck only has 52,000 now. The heads, valves, and pushrods are all good. There is a little verticle scoring in the cylinders but almost no ridge. A...

Here is a video of it running.

It is making a bottom end noise that doesn't sound good. I am going to have to pull it. The explosion was strong enough to blow out a new muffler, so it probably did some damage.

The driver's side muffler is blown out. Both ends are pushed out but I don't see any holes. The passenger side muffler is ok. I just put the dual exhaust on last summer.

The piston is all the way up in cylinder #1 and the line on the balancer is pointing at the zero.

I cranked #1 cylinder to TDC and the rotor is pointing at the firewall. Shouldn't it be pointing to the #1 cylinder?

The original owner was a Dodge dealer in VA. He got this 72 D100 in November of 71. It is points. I am having it towed home tomorrow from the garage a mile away so I can start to work on it. I think there is some serious damage because of the clanking noise. The noise does not seem to match the...

Bump

I have a 2 1/2 hour drive home from Carlisle. On the way home my 72 D100 stalled going down hill on the turnpike. I just put it in N and started the 318 back up. An hour later it happened again going down hill on route 56. This time I pulled off the road because it wouldn't fire up while...

I have the SBP 8.75 axles, backing plates, brakes and drums that I took out of my 68 Dart when I switched to BBP. They originally came out of a 72 Duster 340. The splines on one of the axles looks goofy but they worked well in my Dart. I can bring these to Carlisle. $200.

Good luck. I had a QQ1 blue 68 Dart 270 hardtop when I was a teenager. I love the trim on the side of the 270's.

I got my show field sticker today. I am taking my 72 D100 this year and I am in the blue show field B301. I had brought my 68 Dart the last ten years. The A-bodies have been moved to the green show field.

It was the positive battery terminal. I would have never checked that. I would have been drawing lines to follow my service manual diagrams and disconnecting the bulkheads looking for melted connections. Thanks FABO.

I started my 68 Dart this morning and backed it out of the garage. While pulling it forward to the side of the driveway it just shut off. Now, when I turn the key there is nothing. Tomorrow I will get out my tester and my service manual and try to figure it out. Any advice on where to start will...

PM sent

I will probably get a replacement. It will give me something to look for at Carlisle. Thanks for all the advice.

I just tore down an old 440. One of the rocker arm supports is broken. Is this head fixable or should I be looking for a replacement?

It has a 933 oil pan with a baffle which is interesting. Here is some info from 440 Source. Shown here is an original factory USED "933" oil pan. There were supplied by Chrysler as part number 3751934 in high performance applications which included the internal welded oil baffle, and as part...

Not a crack, just went out and looked closer.

It is 77 440. I took off one of the heads today and the cylinders look okay. I don't really know what I'm looking at though. It had the original metal head gasket. I measured the deck to piston at top dead center and got .156". (I watch Nick's Garage)

I picked it up today. Here is a pic of the top pad and the 440 with a pile of parts. It has the 452 heads and is not locked up.

4006630-440-10 A friend of mine from work wants $400 for this engine. He remembers it coming out of a running police car. What do you think. He wants to know by tomorrow.

Fender Tag Help Here is a thread I made 8 years ago. Post #11 has three pics of my build sheet.

There is nothing hidden under the other tag. White Hat Special package A describes my car exactly. I found two build sheets in my car, one is somewhere in the house. I'll see if I can find it.

I was thinking the same thing. I probably looked when I got the car in 2015. I'm going to check after work tonite.

I have; 2nd row F:1 on my 68 Dart 270, I thought it signified the White Hat Special. 3rd row 1:4, I think it is for sill molding. 3rd row 8:9, I think it is for side molding delete. Do you have better info on these? Thanks 1WildRT.

I pulled in the garage last nite and noticed a puddle under the car. It was power steering fluid. It was leaking out of the cap. I don't think it was overfilled. Has anyone else had this problem? Any advice? Thanks FABO.