Search results for query: *

  • Order by relevance
  1. 22dog22

    69 Cuda ignition switch install question

    I am replacing my ignition switch on my 69 Cuda, 69 is one year only, old switch does not have a contact for a ground wire, new switch has a separate contact for a ground wire, is this needed ?
  2. Swinger 340

    New Build Startup Issue

    Your Disturber housing seems to be correct, so I would say the drive gear is set in wrong. Move your cap wires two notches CW and that should give you your #1 firing position. if everything else is correct. Timing gear and chain is in the right position?
  3. MOPARMITCH

    Stop in for a cup of coffee

    Good Late Morning Mopar Roadhouse Ruffians .........
  4. DionR

    6.1 or 6.4?

    It depends some on your application. Isn't the Dart a racecar? If so, do you plan to race the truck or just drive it? Personally I think the 6.4 with VVT and SRV is the better all around option. More bottom end without losing top end. But...they have weaker pistons and should be swapped if...
  5. W

    Set me straight!

    https://www.google.com/aclk?sa=l&ai=DChcSEwjcyp3NrOOIAxX8X0cBHSpvAdwYABAUGgJxdQ&co=1&ase=2&gclid=Cj0KCQjwr9m3BhDHARIsANut04b_yZA9XACoLcucvU-e3tU84sM3pJ9_Txx3yWo5xpVcXavHHi6Z4AsaAjDLEALw_wcB&sph=&ei=C8P2ZpjOGrWx5NoP-_mW6A0&sig=AOD64_3Fllo_7f-Hc8omv1s7D9madxO6iQ&ctype=5&q=&nis=4&sqi=2&ved=2ahUKEwjY...
  6. Scott_ 69HemiDart

    Stop in for a cup of coffee

    Post away, new recipes are always appreciated.............................:thumbsup:
  7. Sublime one

    Stop in for a cup of coffee

    I got a great recipe for a fish “tartar” sauce we use on fish tacos, but it has some zip! It is yummy. You guys want the recipe I can post it. Man is it good!
  8. lotharamc

    magnum valve train questions

    Low 14 second quarter mile. Not bad for granny's 4dr
  9. Sublime one

    Stop in for a cup of coffee

    Already on it Boss!
  10. 4

    Solid Flat Tappet Valve Springs

    I will
  11. jaws

    Stop in for a cup of coffee

    I think I would start looking for a new Bank, and make sure the bank president knows why.
  12. B

    Solid Flat Tappet Valve Springs

    Same spring I run on my flat tappet
  13. Swinger 340

    Changing crankshaft bearings with the engine in the car.

    You are right on Rusty. I never did a Mopar but have a 454 chevy that way. I loosen the crank bolts a little and do as you stated, easy-peasy. Truck ran for another 5 years before I sold it. I did do the job on my back, but I was a little younger then. Being a truck I have a little extra room to...
  14. Mopar Tim

    Stop in for a cup of coffee

    Soooo we meet again. Real foggy here this am. Stay dry you guys in the path
  15. pishta

    Another gauge corrector--cheaper than MeterMatch, 33.00

    how about running a fuel flow meter and just keeping an eye on it? 15 gallons flows 15 gallons. When the meter has flowed 13 gallons time for a fill up and a reset. No sure how much these are but this one is $35. It may measure way too much like 1-60 liters per minute...
  16. N

    Cam Phasing

    Big difference between an OEM building several hundred thousand units and someone building a performance engine. Not even close. To even advocate that it’s acceptable or even ok to just slap the timing set on and go is bad advice.
  17. jeff alder

    Set me straight!

    You will only get the sound when a switch is true or closed. You also have to be probing the terminals that actually have a contact common to them. You also have to be ware of switches that may be normally open or normally closed. You can also use the same function to ensure your ground is good...
  18. hcallaway

    Ernie's 70 dart

    Fun build!! Been there and done that on the quarter.
  19. 1971 CY Dodge Dart

    CAR COVER RECOMMENDATIONS...1971 DEMON

    https://www.calcarcover.com/?gad_source=1&gbraid=0AAAAAD8XiSaBPYrwMLDUbR3kvUWwnmhiH&gclid=Cj0KCQjwr9m3BhDHARIsANut04bSKDlgA8aKIY4J-9hQOpWihvyfmdhhry5HjeSi5MLoLkdFE62QrD0aAuI3EALw_wcB
  20. Dave999

    Offenhauser \6 EFI

    screw in injector boss Screw in set 8 billet fuel injector boss for EFI conversion | Aussiespeed Street & Racing Products Australia can add injection to any manifold with space enough on the inlet runner jig it, drill it, tap it, done.
  21. N

    magnum valve train questions

    A fast Camry? That’s news to me.
  22. DionR

    6.1 or 6.4?

    No, you can run an 8HP behind a carbureted LA if you want.
  23. Dana67Dart

    Set me straight!

    How many wires are on the switch with the "ball" Photos are very helpful!
  24. MADFORMOPAR

    Last one to post in this thread wins!

    2024 Downtown Milton Car Show - Cars - Google Drive cars at the Milton Ontario september car show. hope the link works.. a lot of pics for sure
  25. Bodyperson

    Cam Phasing

    You didn't miss anything. Well, maybe the original post. "Is the off-set woodruff key for the camshaft itself an acceptable way to adjust the phasing?" If you really want to know the specs, come on over. I'll provide food and drinks. :lol: Fairly mild grocery getter.
  26. lotharamc

    magnum valve train questions

    People build for what they want. That is the case here. IF performanceis all we want we wouldn't be working on a 50 year old car. A camry is faster than almost all of our old cars. Sound IS important. it is significant part of being excited about seeing one of our cars in the wild. When a 17...
  27. ocdart

    2024 14th Annual FABO NHRA "Pick 'Em" Game - It's NITRO Burnin' Time Again!!!

    Current weather in Madison, IL, and updated weekend forecast... Friday - currently light rain falling and forecast be a 90%+ to continue to 4pm tonight. Then dropping to 80% to 7pm and 50% to 9pm. Friday qualifying cancelled due to weather. Saturday - 40% chance of light rain starting about...
  28. 3404spdfish

    Just got this 1966 Dart GT

    i have a 66 dart 270. 273 auto car with 7 1/4 rear. i have slightly a different trim but is that the only difference from GT and a 270
  29. 4

    Impending surgery: Prayers Requested!

    Wow,,, what an intriguing story. You have done things right..( sorry about the woman) but you and your son are a credit to your gender..what winners !!!! It’s an honor to have spoke, if you are ever near Des Moines Iowa, stop by for a cup of coffee. And we can talk shop..
Back
Top