Search results for query: *

Do you guys run synthetic gear lube in your cone style suregrips? I installed a 355 that has been sitting in a bucket for years. I used Valvoline synthetic gear lube and Red line friction additive. I only drove it about 5 miles but it is chattering going around the corners. Maybe it just needs...

What do you guys use for suregrip additive? Also how much to you add to your gear lube? It has been about 12 years or so since I have swapped out a 3rd member. Going from a 410 locker to a 355 suregrip...

What is the best way to add a vent to my 727? Transmission is in the car. I am having issues with the dipstick popping out. Thought about drlling a small hole in top of the dipstick right below the handle.

My transmission dipstick always pops a good part of the way out when driving.Fairly stock 383,727 TCI trans,and 410 gear. Any fixes for this?

Anybody have luck sealing a leaking front seal using Lucas tranny additive?

Anyone have a pic of a B or A body torque shaft? I think the ones I have are for a 904 tranny.

Narrowing a rear end and welding on spring perches. What should the pinion angle be at?

What does a factory 1968 904 converter stall at? Ordering a Hughes converter either a 2000 or 2500 stall.318 Low comp ,small cam headers, 4 bbl ,904 ,373 gear,71 Dart

On a 8.8 rear end conversion are you guys using 8 3/4 u bolts and shocks plates?

Who here runs a Hughes comverter? How well do they hold up. I just have a 275 hp 318 with 373 gears.

Who sell stall convertors for a 1968 904 automatic? TCI list 72 - 80 transmissions only. B&M list only 727's. Wanting a 2000 stall.

Anybody have a make and part number for the u-joint when going from a Mopar driveshaft to a 8.8 rear end

I got a narrowed B Body housing with my Barracuda.It measures 51 7/8 from flange to flange.Will stock small bolt A Body axles fit this housing? Thanks,Jim

My Buddy has two suregrip chunks.The first is a 489 case 323 SG.The second is a 741 case but I do not see a gear ratio stamped into the ring gear.Matter of fact the ring gear on the 741 case is much beefer than the one in the 489 case.The teeth are bigger and the ring gear is wider.I did see a 6...

I have a 3 speed shifter,handle,and rods that I pulled from a F body wagon years ago.I assume it was a 3 speed overdrive in the F body.Can I change my 71 Duster to floor shift and use this set up.I believe it will work but I am not sure... Thanks,Jim

Ok I have a slant 6 3 speed on the tree.Can I bolt up a 4 speed up to the 3 speed bellhousing? If so will the drive shaft bolt back up,or do I need to modifiy it? Thanks,Jim

This maybe a dumb question but here it goes.Will a 11 inch clutch and a 142 or 143 tooth flywheel fit in a stock A body 383 bellhousing.I can not remember how many teeth are on my my flywheel.I am guessing it all will fit fine, but I just want to make sure...

Has anyone used a hydraulic throw out bearing and master cylinder in there big block A body? If so what name brand do you have? And how well does it work? Jegs sells a hydraulic throw out bearing for a 23 splie a883.I was thinking this bearing with a wildwood master cyclinder...

If I put a 4 speed behind a smallbock with a cast crank what flywheel do I need to use???? All the ones in Summit say for neutral internal balance.And a cast crank is external balanced. Thanks,Jim

I have a 1995 Dodge Dakota with a 3.9 and automatic transmission.Lately it has not been shifting into overdrive,sometime it will but other times it will not.Is there a switch on the transmission going bad,a relay somewhere,transmission filter dirty,or is the tranny about to quit on me?? Any...