Search results for query: v8 throttle cable

If your 6 had A/C you can use the throttle cable, but the non AC linkage throttle contraption wont work. Get the kickdown from the V8 too.

you want dirt cheap >>> 73 duster slant six 3 speed car of which the slant six was pulled and tossed in a ditch 318/727 off CL for 400 bucks cheap *** summit headers 120 bucks (optional) though you would need the correct manifolds conversion mounts 80 bucks 88 lebaron radiator and shroud...

Sorry, the center link and the throttle cable are spoken for. yes that is an 8 track, It is very dirty and I HIGHLY doubt that it works. If you want to take a chance on it, PM me and I will pull it for you The spare tire wells are shot on both cars. The seat bases are available, out of the 4...

For you early A guys looking to swap to a V8, you'll need the V8 gas pedal bracket assembly, V8 gas pedal and the V8 center link. Here's your chance to grab all three correct pieces at the same time. No throttle cable. The 2nd picture shows the firewall plate that holds the inside bracket...

your 77 360 does not have sensors, only water temp and oil pressure senders. trans mount is the same. you will need the pre 73 biscuit style rubber mount. just to re-cap for you 360 car engine mount brackets and pre 73 rubber mounts pre 73 rubber trans mount you will need to take 4" out...

will a throttle cable from a /6 work for a v8? the one i have was for the /6 but since i dont have a carb on my engine i dont know if it will work for my v8.

I have a good used gas pedal with a V8 throttle cable. Came from a running 318 1974 Plymouth Valiant. Locatred in Raeford NC 28376 Paypal accepted $45 OBO shipped in the US.

i need a throttle cab that will work with my 360. my /6 cable is too long.

if you are using a 360 904 you can use your driveshaft. if you are using a 727, you will have to wack 4 inches out of it, and you will need the 727 yoke. the trans mount is the same i have been running my 7 1/4 , 10" front and 9" rear drum brakes and torsion bars for over a year now and it...

not really, the throttle cable is rather long for the V8, the kickdown is totally different (is yours a 1 or 2bbl?) 2bbl carb can move over to a 2bbl V8, keep everything so when you get bored of another V8 Dart, you can go back to the leaning tower of power...;-) let me know if its a 2bbl...

If I were to get oem throttle cable for a v8 would one from a 72 dart or 70 dart work for my 73 duster and would anyone know the overall measurement for the cable thanks

...(new) I think I $50 for it (offer) manual brake push rod $20 66 & under t sig arm (nice chrome) $10 fan spacer $5 67-72 v8 throttle cable with clips $20 drip rail chrome corners $10 per set headliner bow retainers misc pkg #1 valve cover oil cap,dash to body rubber fillers,rad...

That's pretty cheap all right, butr how much bang did you get for your buck (how fast is it?) This guy put a Buick turbo (175$ at a junkard) added a 4-bbl l carb and a Clifford intake and ran 12.95 @ 104 with what is basically, the engine you threw away. Is your car faster than that...

Original V8 4 barrel throttle cable ? Drive shaft for 904 to 8.25 rear ?

...904 A/T. He put a 440 in it and sold the 318 and 904 to me cheap so we put them into my 65 Barracuda. At the time I didn't have a V8 throttle cable so we ran safety wire from the column shifter through the firewall to the carb. I drove it to the MOPAR Nationals a few weeks later and did...

I need a V8 throttle cable. Got one? How much sent to 42450. Thanks.

Dash is installed-grounded to dash. I actually have an extra wire that I hooked to one of the screws on the back of the dash cluster to better ground it. The dash cluster lights work-so I was guessing that the gauges are grounded?? Im about ready to just rewire all the wires at the bulkhead and...

Hello, I am likely going to be building a budget pre 73 A body with a V8. The car currently has a /6 and an automatic and is complete. I have parted several 73-76 A body's and a few trucks etc. I have most all of the linkage etc. from all of them. I also have a 72 v8 with manifolds...

Superslant I like Eddy 140X carbs so any Carter would be fine. A small Holley should be easy to fine as well. Look for a V8 A body for the cable conversion parts and take pedal to the carb. Use a Lokar or Buchilon (SP) cable to do your kickdown. On your 63 you dont have part throttle kickdown so...

Like I said, you have a 318 2 bubble kickdown rod installed backwards, with a 318 acelerator braket that has been bent up. Look at your pic and 65 vals pic. Notice how his throttle cable goes under the kickdown rod ? Notice how his kickdown rod bends up ? Also notice how his k/d rod is...

I sent a PM...Did you get it?? 8)

I also have a spare 7? Dart V8 throttle cable and bracket.If you need it let me know the length you need and I,ll check to see if it,ll work for ya.

will the throttle cable from a /6 work on my v8 swap if so i don,t need that. i also found the top water pump pully.

Is there a differance in length between the 2 barrel V8 cable and the 4 barrel cable on an early A?

Im not sure of the measurements,but as I found out,my old /6 throttle cable is longer than a v8 one.I was wondering when I was driving it the other day why I had the pedal to the floor and it barely was moving .I opened the hood and found it wasnt opening the throttle on the carb all the...

Can't help with the parts (sold one at the Nationals) but you can widen the search as a 65/66 slant with factory AC uses the same throttle assembly but a different cable.

Hey All, I have just installed a offy 4 bbl intake on my /6. Now I need to modify the throttle linkage to connect to the carb. Does anyone have pics of your linkage so I can (hopefully) make a bracket? Also, do I need to get a v8 cable and run from my pedal? Any input would help out greatly...

...paint. Re-coated the top of the throttle cable groove with rubberized paint. I am still waiting on purchasing the correct V8 throttle cable, and foam gasket, then I can call this done! While I had the phosphate paint, I went ahead and also blasted/painted most of my hood latch...

the throttle canle seems to be working fine. if i remember right, when i did the engine swap i used the /6 cable with the v8. should i get one for the v8?

I need a V8 throttle cable for my '65 barracuda. Preferably one that is in decent condition. This is the last part I'm in need of for my V8 swap. Thanks.