Search results for query: *

One reason PCVs get disconnected is because a bigger cam is installed in the engine, & these have less vacuum at idle. Not enough vac to pull in the pintle inside the PCV..... So the PCV gets disconnected....

https://www.doctordiff.com/blog/tech-info/rearend-pinion-comparison/

This is going to sound whacked, but I have done this dozens of times with success. Dress the crank and or rod journals with crokus cloth strip. Take the bearing halfs out of the cap and drag the cap on a good file switching ends every other stroke to help uniformity. (Dragging it toward you...

Want to make sure what it really is that you are feeling with your fingernail going across the crank journal. A lot of times the softer bearing material will transfer to the harder crankshaft, and that softer bearing material will easily polish back off. That is where the 320 wet/dry with...

"clean title" doesn't mean **** you want the plate and the last 5 of the VIN to run thru the DMV reg fee calculator online. that will tell you if any back fees are owed on the car and what it will cost to transfer and reg in your name. if the seller's name isn't on the title, no go. if the...

Except they all have Russian made diesel engines in them nowadays. Tom

It's a hydraulic system fellers. Lets not over think this. A standard hydraulic jack oil will work fine. IF I was gonna use transmission fluid, I'd use Type F since it is hydraulic fluid and has no detergent that might damage seals.

We still have yet to meet up in person. Any thoughts on that for the near future?

320 wet/dry & WD-40, then can follow that up with a scotch bright pad, then follow up with the final crocus cloth for the final polish. Plug the oil holes with some high density foam to keep the gray matter out of them while doing this. ☆☆☆☆☆

You'll want to disconnect any linkages such as Z bar for a manual or the column shift if it's an automatic. Maybe even disconnect the manifolds form the pipes or the headers from the collectors. We don't know what you have since you didn't say. I always do both mounts at the same time because...

Unless you were testing to see the amount of timing retard the individual parts are contributing to the systems total amount of retard. So far, single point, dual point and unilite distributors by themselves appear to contribute very little timing retard as a trigger for the distributor tester...

You could make that easily. Polish a piece of 18 or 20 gauge metal and then cut it, then file the cuts smooth and polish again. Then spray on a few light coats of rattle can clear for rust protection. Then dip it in that black rubber stuff that you can dip tool handles in. If done carefully...

No just some notes about disconnecting some linkages and pulling the dist, etc.

Still hurts :( This Saturday I'm going to the last day for a local wrecking yard to do a final pick, several 60s and 70s A bodies all will be toasters in a few months

Either on Facebook or here I recently saw someone selling LH msg type lug nuts. If I see it again I'll copy the address forvyou

Maybe it was resurrected by new people who will do it right. I wonder what would happen if @Righty Tighty contacted them and asked for a new hood? Perhaps they would do something. It wouldn't hurt to try.

Only thing might be detergents and seal swelling properties of ATF might be different but I don't

If you watch eBay etc you can find NOS gauges for a reasonable price. Realtime engineering RTE limiter - rte makes a great IVR. Replacement cir boards are available. I sell a gasket set for 67-71 dart clusters. The temp sender is easy at the auto parts store. The tough one is the fuel...

TF Justin Ashley FC Jack Becman PS Dallas Glenn

Well alrighty, Buckaroo. I guess he shouldda asked you first.

Transmission is in. Took it for a drive and everything seems to be working fine. Stalled the new converter up to 3500, and it may go a bit higher, but the engine is bogging hard. With no changes to the tune it’s running pig rich under boost; under 10:1. Double checked the fuel pressure, and...

I've had their converter since 2000. When I damaged the snout they fixed it extremely affordably. Very friendly guy on the phone, a quarter century ago. Offered to give it extra stall while apart but I didn't need it. Doing great roots blown no problems.

72 72 overtime @Sublime one

So it was a reference to a Bruce Willis movie ? The only actor i avoid more than him is nicolas cage BUT, i will say this, a few months ago i watched a flick with Willis in it that wasn't half bad, I believe it was called the 6th sense Reminded me of "the others"

Can't forget, they sound good also.