Search results for query: *

Thanks for all of the advice given. I just thought that I would give an update. I ended up going with the 14x28 metal shed. I did have them add another layer of 5/8 flooring on top of the 3/4 treated plywood floor. I put the car in it today for the winter and everything seemed fine. Next summer...

I just looked at the sheds for less website and prices have gone up a lot from what you posted (I am sure due to prices now vs pre-covid). A 12x24 garage is listed at 8,599 and that does not include the garage door, shingles and roof trim or paint.

Thanks again for all the replies on this. Yes I do need a building permit and it has been approved. I am not sure if a shed would be taxed or not but probably in my town. In the long run a garage with a poured pad would probably be better but for timing now the shed is a better fit for me. The...

Around here it is just standard for them to block it. It is a extra charge to have gravel brought in and leveled but I think it is worth it as it will only be as good as the base that it is on.

Thanks for the replies so far. I will also have the people come in and put down the gravel base and level it properly so hopefully that will help it be as sturdy as possible.

I am looking at buying a prebuilt portable garage shed that would be 12x28. I would be buying it store my duster in it over the winter along with some other stuff. Does anyone here use one for car storage and if so how is the wood floor holding up? The specs on the floor would be 2x6 floor...

Thanks for the info so far. I will wire it using the starter relay.

I am starting to install a painless wiring harness into a 69 cuda that is in process of being put together. The car is not going to be stock so factory appearance and workings does not matter. It looks like the instructions show how to do it without the factory starter relay on one page and then...

Just curious if anyone makes a complete terminal and connector kit for mopar vehicles. I would like to use one of the universal wiring kits to rewire my car but I do not want to reuse my current connectors and ends. I know painless and some others make mopar specific kits. If you have used one...

Thanks for the replies

I am looking to see if anyone is or knows anyone who is a janitorial equipment (floor scrubbers etc) tech or a packaging equipment tech. Looking to hear about the pros and cons of it. Thanks

This is mine with a b-body 8.75 and mopar ss springs.

Looking to see if anyone has a shift r gate for a reverse pattern valve body that they want to sell that fits a a-body?

I have the white gauges that come as one piece. So far I am happy with mine.

Thanks for the tips. It turns out I had to look in a 1973 fsm diagram. That wire does go to the seatbelt warning system off of the splice.

Thanks for the replies so far. I must have the simplified version because it looks just like the one on mymopar site. It IS a fused circuit. If I remove the second fuse in labeled Brake LP power on the circuit goes away. I know for sure that one of the wires off the splice goes to that relay or...

Hi everyone I was just trying to clean up the wiring on my 1972 duster and I have a question on what a wire all runs to. I have the manual and I can not find in the wiring diagrams I have where it shows this wire coming to and from the fuse block. The fuse block is labeled brake and LP for the...

What you guys are saying is what i found when searching. Some people say with some filing they work great and others say they took it back out. Now i just need to decide if its worth trying and messing with it or not.

Is anyone using the shift-r-gate in their shifter? I was looking at buying the version for the reverse manual valve body. I searched this and found some old topics but nothing recently and it went both ways,some people said it worked good and others said it caused the shifter to hang up. Just...

No this will not cause any codes. I have replaced a few tanks for this problem. It will only be a tank problem if it only happens right after fill up. Try not filling tank above 3/4 for the next few times,if the problem does not happen again with tank only 3/4 full then you know.

If the problem is only after filling the tank full you probably have a bad shut off valve in the gas tank causing gas to get into the canister and the evap system. When this happens the car will stumble or stall until the gas is sucked out of the evap system then it will be good until you fill...

I tried to search this and I found lots of info on the newer style clips but not too much on what mine look like. I am trying to find where I can purchase new clips that go between the wiper linkage and the pivots? Here is a pic of what mine look like. Thanks

If you look up that part number it shows it only fits the 360 and does not fit the 318 or 340. I thought all the la 360's were externally balanced?

I have for sale a 727 valve body with a transgo TF-3 kit installed making it a full manual valve body. I recieved this valve body in a package deal with some other parts I purchased. I do not know to much about it and have never used it but was told it is clean and works. Asking 40 plus...

I have that cam in my 408. I run 3.55 rear gears with a 9.5 inch torque converter with 3200 stall. I mainly street drive it and it works good. When i was calling around on a converter everyone was between 3200-3500 stall. I am running 255-60-15 rear tires.

I will take it,Pm replied too

Pm sent if 66340sedan was not first.

Do you have any fuel sending units with working level unit? I am lookin for one to cut up and try to mount in my fuel cell.

Looking to see what size air filter you are running on your car. I have a 408 in a duster with a air gap intake and I am trying to see if a 14x3 air filter with a drop base will fit? By measuring it looks close but I would like to know before I buy one.

How much for the ram fuel door and what years does it fit?