Search results for query: *

Hello, Does anyone have a recommendation for Edelbrock's 5777 springs? They seem to be discontinued. https://www.jegs.com/i/Edelbrock/350/5777/10002/-1 Jeg's alternative is a dual spring which the 7177 cam manuals says not to use...

Looks like speedmaster is having a Top End Engine Combo Kit promo. Not sure how much work would be required to get this to work well.

Hello, I have been working on getting my car up and running but keep running into a lot of little things here and there. I have a 74 duster with a 360. It has an edelbrock performer rpm camshaft that came with hydraulic lifters. The problem is that I keep getting excessive noise from the...

Hello, I was cleaning my shed and came across some old parts. I would like to know what price I should sell them for and if they are what I think they are. Looks like a Mopar duel plain aluminum intake for a SB 360 Looks like a Holley 1850 (600 CFM double pumper?)...

Hello Guys and Gals, It is that time of the year when I get to work on my car. I got her started up a few months back but didn't notice this noise since the exhaust was off. I thought the valves needed adjusting so I went through and adjusted them according to some videos I saw on youtube...

Hello, Last week I was helping my brother get his car on the road again. It is a 72 duster with a 318. I has not been rebuilt rebuilt from what I can see and seems to be in need of one. Anyway, It doesn't want to start unless the timing is set to 30+ advanced. It is nuts! I guess it was...

Hello I just spent this weekend trying to get my engine that has been sitting for 6yrs to run. I kept it dry and oiled during storage but it was outside (condensation?). I have not been able to figure out what is wrong with it. I have replaced the starter and battery. It didn't change...

Well i was looking around ebay and came across these. I thought they looked nice. My car is not near to complete to be thinking about shiny bits but maybe you guys are interested. I am a bit concerned that they used vinyl stickers but it says they are heat resistant. hmm i gotta see that to...

How have you guys with this pan gotten your engine in?(milodon pan 30935) I have 74 duster with 360 and power steering. Im using an engine lift with the angling thing on it to get it in but i can't seen to get the bottom left corner to clear the k-member, there is about 1/2 clearance issue.

I have my engine bolted to a stand but it is bending and not letting me rotate the engine. What holes do you guys use to support the engine? Im using the ones on the sides or the heads and two where that trans bolts to. Also the stand didn't come with bolts to bolt it to the engine.

Ok so the book i have says 30ftlb, but i just broke a bolt. this is a recently machined head with the bolts that were on there before. Is 30ftlb the right torque? hmmm im also having a hard time finding where to buy some replacement ones... What about for the rest of the top end? (intake...

How do i tell what ones i have? I need to find out what lash i need to set.

I pull two of my vales off and was not sure if they were seating correctly. does it look like i may need a valve job?

So i was started to replace the seals on my heads today and noticed that the seals that were installed are not like the seals i got from the parts store. It looks like all the seals but one are the same and that one is the only one that looks like the ones i got from the parts store. These...

Im having trouble deciding wither the paint the whole engine including intake or not. Also paining it the same color as the car. So could you guys post up your engine bay pics?

So i pulled my heads off yesterday and noticed that in one of the cylinder walls it has some rust about 1/5 of the top. i guess some water got into the intake :angry5: what should i do? I think the intake valve has some surface rust too.

Ok so im pulling off the heads on my 360 this weekend but want to find out some things first. Is there a nice step by step on this? Is there a place that list the torques that the bolts should be at when i put it back all together? I have heard it is easy to do but i have never dune it and...

Any one know of some good stock height valve covers with thick flanges that wont warp when i bolt them down? The simpler the look the better looking for a stock look with hidden goodies inside.

so this weekend i installed a complete kit from milodon pan, pickup, main studs, and windage tray. i followed their instructions but they didn't have me put any lock tight on the main studs or bolts for the tray. they did say to use fine oil and check the threads. Is this correct? also is there...

Hi i was hoping i could get some help to find a leak. My car had a pretty bad leak but wasn't sure how to check the gaskets or rear main seal. The engine is out of the car right now and would be the best time to do any repairs i imagine. Also would be the right way to install the oil pan, valve...

I have what looks like the stoke harmonic balancer on my 360. Should i replace it when i do my engine rebuilt? What do you guys think about the rattler harmonic balancer?

Are there any nice looking stock hight valve covers? I have a 7" brake booster so its really tight and the only ones i can get to fit are my stoke ones. The stoke ones are ok, but i want something that looks nicer.

I bought this kit from jegs and i just want to make sure the pan will fit my stock k member. -74 duster 360 http://www.jegs.com/i/Milodon/697/31940/10002/-1/752328|10457

Has anyone tried these? Some clam to reduce friction and temps.

Ok so i have been saving up and im ready to take things apart. I don't plan on rebuilding it because i have never done one before and i kinda don't want to have to pull it out again. my 360 sounds like a coffee grinder :( What do you guys think it might be? It sounds the same in all gears so...

im looking to get a forged crankshaft for my 360. Its a mild setup engine. What should i look for? What stroke is stoke on a 360? What is cross drilling?