A virtual Dyno said this...

-
Brooks James

Brooks James

VET, CPT, Huey Medevac Pilot
FABO Gold Member
Joined
Dec 12, 2020
Messages
5,537
Reaction score
3,712
Location
Fruitland Park Fl
Virtual Dyno says
530 wheel HP / 470 tork

Stock 360 Magnum, block, crank, heads, pistons 60 in the hole

Cam adv
498/512
274/286

a 100 shot Shot under each carb on manifold below total 200 hp

Or a race built thermoquad, I found
A guy who builds class winning tq's
$$$

Rpm Air GP

MP dizz

What do you think ?⁷

17284261456253940000393198608062.jpg
 
Last edited:
If you can tune it, I could see a fairly stock cammed magnum with a 200 shot getting to 520-530. How long will it live there, depends on if you can tune it.

Edited to add;
I have a magnum crate that I bought from westech that was used as a dyno mule. With a small comp roller cam and an rpm air gap, headers and a 750 it made 365 so it’s not too far of a stretch to 530. Maybe not at the wheel though.
 
High doubts with those carbs and that manifold.
But give it a shot , id like to have a new opinion on that stuff.
 
MOPARMAGA said:
High doubts with those carbs and that manifold.
But give it a shot , id like to have a new opinion on that stuff.
Click to expand...
I was a little confused by the post. His picture suggests dual quads with 100 plate each, but he says rpm ag in his description.
 
TT5.9mag said:
If you can tune it, I could see a fairly stock cammed magnum with a 200 shot getting to 520-530. How long will it live there, depends on if you can tune it.

Edited to add;
I have a magnum crate that I bought from westech that was used as a dyno mule. With a small comp roller cam and an rpm air gap, headers and a 750 it made 365 so it’s not too far of a stretch to 530. Maybe not at the wheel though.
Click to expand...
I was thinking my setup was close to a 380 crate pls 150 HP equls
MOPARMAGA said:
High doubts with those carbs and that manifold.
But give it a shot , id like to have a new opinion on that stuff.
Click to expand...
I'm aware that single 4 can easily out pace,I may be more willing to use the duals if I want more eye Candy.
It depends on what the engine pieces look like together
 
TT5.9mag said:
I was a little confused by the post. His picture suggests dual quads with 100 plate each, but he says rpm ag in his description.
Click to expand...
Either or more

Race thermoquad on the Torker
200 HP plate

Race TQ on air gap

Dual quads 100 plates under each car

530 hp total
 
Brooks James said:
Either or more

Race thermoquad on the Torker
200 HP plate

Race TQ on air gap

Dual quads 100 plates under each car

530 hp total
Click to expand...

Gotcha. If I was trying to make 530 at the wheels on N20, honestly none of those would be my choice. Maybe, and it’s a strong maybe I’d use the rpm air gap but not with any of those carbs. That’s just me, I like Holley carbs. And a Holley would be on a good (Victor or similar) single plane. On magnum heads you might be limited to the Indy or M1 for a single plane.
 
Thanks, "it's use what you have" for me now
I've never been off a budget, and my wife handles the money
What does that tell you ?
 
TT5.9mag said:
Gotcha. If I was trying to make 530 at the wheels on N20, honestly none of those would be my choice. Maybe, and it’s a strong maybe I’d use the rpm air gap but not with any of those carbs. That’s just me, I like Holley carbs. And a Holley would be on a good (Victor or similar) single plane. On magnum heads you might be limited to the Indy or M1 for a single plane.
Click to expand...
Yes, I want something that is highly adjustable
 
i don't think you get there with stock heads and compression and that small of a cam with any of those combos.

i'd run it back and simplify with a single carb (holley) and maybe you see the top of the mountain with an air gap, but likely you need a single plane and flow which presents the bottle neck of the heads flow capability above .500 and compression.

so doable, but real tough row to hoe with the combo of parts you've got.
 
air gap
tuned 750 dp
that motor na should make 400 plus torque
a 200 shot will give 200 plus lb ft torque more torque then hp
 
a-bodyguy said:
air gap
tuned 750 dp
that motor na should make 400 plus torque
a 200 shot will give 200 plus lb ft torque more torque then hp
Click to expand...
More than 530 tork ?????
Look like I will be ordering a set of 3500 lb SS springs
And some MT street drag radials
 
Last edited:
Brooks James said:
I was thinking my setup was close to a 380 crate pls 150 HP equls

I'm aware that single 4 can easily out pace,I may be more willing to use the duals if I want more eye Candy.
It depends on what the engine pieces look like together
Click to expand...
What intake is that ?
Is it a offy split single plane?
 
Brooks James said:
Virtual Dyno says
530 wheel HP / 470 tork

Stock 360 Magnum, block, crank, heads, pistons 60 in the hole

Cam adv
498/512
274/286

a 100 shot Shot under each carb on manifold below total 200 hp

Or a race built thermoquad, I found
A guy who builds class winning tq's
$$$

Rpm Air GP

MP dizz

What do you think ?⁷

View attachment 1716313309
Click to expand...
For future reference when you say 60 in the whole, it is correctly written as .060 just so nobody gets confused.
 
Brooks James said:
More than 530 ?
Look like I will be ordering a set of SS springs
Click to expand...

junkyardhero said:
i don't think you get there with stock heads and compression and that small of a cam with any of those combos.

i'd run it back and simplify with a single carb (holley) and maybe you see the top of the mountain with an air gap, but likely you need a single plane and flow which presents the bottle neck of the heads flow capability above .500 and compression.

so doable, but real tough row to hoe with the combo of parts you've got.
Click to expand...
Torker is single plane
Have a worked 750 dp
Now I'm figuring possibilities

Even with my suspension worked
On 23560r14 MT street drag radials tires it will still be a tyr fryr
 
a-bodyguy said:
air gap
tuned 750 dp
that motor na should make 400 plus torque
a 200 shot will give 200 plus lb ft torque more torque then hp
Click to expand...
To make around 600 hp at crank around 5400 rpm, it would take about 575 tq at peak hp and probably 600+ tq at peak tq.
 
273 said:
To make around 600 hp at crank around 5400 rpm, it would take about 575 tq at peak hp and probably 600+ tq at peak tq.
Click to expand...
Oh oh, cast crank and hypereutectics here, may have to tune down to 500 HP, also not sure magnum block can handle 600 HP while on nitrous
I won't forget to get an MSD 8680, dash adjustable timing, offering up to 7.5 degrees plus or minus degrees

I'm Thinking NO GO
 
Last edited:
273 said:
To make around 600 hp at crank around 5400 rpm, it would take about 575 tq at peak hp and probably 600+ tq at peak tq.
Click to expand...
i said 400 tq NA and 200 tq from a 200 shot of spray never said anthing about 600 hp
I said it will make more torque then hp
600 x 4500 = 2812500 div by 5252 = 535 hp
Its more then enough
 
You must log in or register to reply here.
-

Back
Top