crank upside down
- Thread starter angeldust72
- Start date
-
OldVart
Well-Known Member
As long as the muffler bearings are installed correctly, the upside down crank shouldn't be a problem. 8) Please refer to picture for proper muffler bearing installation procedure. :-D
IfItsGotWheels
XS Tech-Anything worth doing, is worth doing in XS
Damn, now I know why my Jeep isn't climbing trees anymore. I checked online and couldn't find muffler bearings for a 1999 Cherokee. Will the bearings from a Chubby fit??
BWDart
Well-Known Member
I worked in a Mercedes parts dept for a short while they actually have a listing for muffler bearings!!!!
demon seed
The Original Demon Seed
One of the most important things to remember is that loose holes are bad and tight holes are good, "boy are they good".:-D:-D:-D:-D
Terry
Terry
chasduster
Well-Known Member
jomoper
Mope or Nope
well ya got me angeldust72 :-D
Thanks we all got a laugh outta this one .
Thanks we all got a laugh outta this one .
OldVart
Well-Known Member
Obviously Terry has been lookin' for love in all the wrong places Jack. 8)
demon seed
The Original Demon Seed
moper
Well-Known Member
Maybe the car is just upside down.. try rolling it over.
These universal muffler bearings should get you where you need to go. Please don't defile your Jeep with Brand-X parts.
jjr426
Well-Known Member
This has got to be the funniest thread I've seen in a while I was cracking up sitting here reading it. My wife keeps asking me what is wrong with me. Thanks I needed that kind of a laugh today
angeldust72
Active Member
I like everyboy's suggestions to remedy my upside-down crank. I think I'll first flip the car on it's top then the crank will be right side up. However, I have come to the conclusion that then the tires would be up in the air and I wouldn't get much traction, yet we are expecting snow this weekend and I shall use the Duster for a sled with the kids and Cocoa etc. then to solve the upside down car issue, I'm gonna diga a hole to China where then the car will be right-side up again (then I'm gonna sell it to those Chinese , pay-back for those bad toys, food and and drywall they've been selling us...that'll teach them not to scew with us MOPAR guys, by gar)
fishy68
Tyr Fryr's Inc.
george
Well-Known Member
ROFL! My vote for best comeback!
dodgetkboy78
EDELBROCK HEADS SUCK!
Every crank I put in has been upside down........ they are too heavy to hold up when your putting the maincaps on.
intimidator
Mopar or No Car
It must be a Ford. Flip it Over and Read the Directions. That is unless it was Found On the Road Dead.
angeldust72
Active Member
dug the hole through to China, but it got so hot in the center of the earth that the tires melted off and the Chinaman did not want to buy the Duster. (ONe guy wanted to turn it into a rickshaw, trade a bowl of fish heads and rice for it,told him it was an original 340 Duster Hemi orange until the paint melted off and originally owne by Chairman Mao...he didn't buy it or the Duster) Anyway coming back to America by sea. Dusters are real water-tight if you have all the body plugs in. I'm gonna put a propeller on the propeller shaft (some people call it a drive shaft) and motorboat back to Arkansas.
By the way I finally did get oil pressure, found out that the oil pan had a dent in it (somebody had apparently jacked-up the car on the oil pan and had caused the pick-up to be canted and sucking air)
By the way I finally did get oil pressure, found out that the oil pan had a dent in it (somebody had apparently jacked-up the car on the oil pan and had caused the pick-up to be canted and sucking air)
-
