''I'm going to fix it up someday'' The resurrection of a '74 Dart Sport......

-
it is nice to see some thing that has been put to rest have a second chance! keep the pic's coming
 
First was the engine compartment painting.
I didn't go fancy here, it just needed freshening up. There was only light surface rust on the upper inner fenders which came off with a wire wheel pretty easily as well as the master cylinder area. then i sanded everything thoroughly. Everything was removed except the heater motor, (to be changed later) and the e brake cable. I self etch primed the engine compartment and painted with Duplicolor ''perfect match'' KG8 Deep Sherwood Green paint, (the original color for the car.) I couldn't believe that my local Canadian Tire store had it in stock!

View attachment 20121116_78.JPG

View attachment 20121116_72.JPG

View attachment 20121116_79.JPG

View attachment 20121116_81.JPG

View attachment 20121116_73.JPG

View attachment 20121116_80.JPG

View attachment 20121116_82.JPG

View attachment 20121116_83.JPG

View attachment 20121116_84.JPG
 
Moving right along and in great style some good work going on here for sure :cheers: watching these great builds makes for a good :coffee2: time :glasses7:
 
I rewelded the lousy factory welds on the K member......
 

Attachments

  • 20120824_23.JPG
    165.7 KB · Views: 1,158
  • 20120824_21.JPG
    161.9 KB · Views: 1,113
  • 20120824_14.JPG
    152.5 KB · Views: 1,099
  • 20120824_13.JPG
    145.7 KB · Views: 1,126
  • 20120824_12.JPG
    148.5 KB · Views: 1,142
  • 20120824_11.JPG
    172.8 KB · Views: 1,125
  • 20120824_6.JPG
    168 KB · Views: 1,139
  • 20120824_5.JPG
    165.8 KB · Views: 1,136
  • 20120824_9.JPG
    133.7 KB · Views: 1,131
  • 20120824_8.JPG
    170.6 KB · Views: 1,168
memike said:
Moving right along and in great style some good work going on here for sure :cheers: watching these great builds makes for a good :coffee2: time :glasses7:
Click to expand...

Thanks, Mike.
Yeah, it's a lot of work......but very rewarding.
I did all of the welding and fabricating myself on this project, so if it leaks or breaks, i can blame you know who! :D
 
It's kinda tough welding on a old K member with just a mig, even being sand blasted and ground out, there is still crap that seeps through the pores and seams......
Still a lot better than the factory!

View attachment 20120824_38.JPG

View attachment 20120824_42.JPG

View attachment 20120824_44.JPG

View attachment 20120824_46.JPG

View attachment 20120824_45.JPG

View attachment 20120824_48.JPG

View attachment 20120824_47.JPG

View attachment 20120824_35.JPG

View attachment 20120824_33.JPG

View attachment 20120824_49.JPG
 
gdrill said:
Nice welds Tom....I see you're not just another pretty face! :D
Click to expand...

Thanks George.
I think they are kinda groty, yeah, i know...... just like my face. (I saved you the trouble of saying it!) :glasses7:
 
Well, why wait? On to the engine!
It's a '78 casting date 360 out of a '80 Chrysler. Ran pretty good, good oil pressure, no squeaks, ticks, or rattles...... compression checked out good too.
I pulled the intake off, and found lots of sludge inside. Under the valve covers was just as bad. The timing chain was really bad and the cam was starting to go flat. Surprisingly enough, the pan was quite clean, and the cylinders had barely any ring ridge at all.
 

Attachments

  • 20121116_43.JPG
    197.6 KB · Views: 1,067
  • 20121116_37.JPG
    189.2 KB · Views: 1,068
  • 20121116_35.jpg
    98 KB · Views: 1,094
  • 20121116_34.jpg
    95.4 KB · Views: 1,064
  • 20121116_33.jpg
    117.1 KB · Views: 1,076
  • 20121116_28.JPG
    168.1 KB · Views: 1,097
  • 20121116_2.JPG
    198.5 KB · Views: 1,085
  • 20121116_4.jpg
    115.5 KB · Views: 1,078
So we proceeded to have the heads cleaned up and the valves ground, the guides were all good if you can believe that, the surface on the heads were straight and flat still as well as the decks, shecked for cracks and found none, had all of the tin and hard parts cleaned up at the machine shop as well.
We went to work cleaning the inside of the engine and all of the water passages. We found 3 frost plugs and 2 old block heaters in there that we had to remove!
In went the 474 lift purple shaft cam and double roller timing chain set we had laying around, all new brass frost plugs, block heater, water pump, and all new gaskets and seals.
Also had a Weiand 4 barrel aluminum intake that i got a few years ago, cleaned it up and installed it.

View attachment 20121116_38.JPG

View attachment 20121116_40.JPG

View attachment 20121116_39.JPG

View attachment 20121116_41.JPG

View attachment 20121116_48.jpg

View attachment 20121116_50.jpg

View attachment 20121116_55.JPG

View attachment 20121116_57.JPG

View attachment 20121116_58.JPG
 
Paint time! :D
Time to make it purdy.........:glasses7:
 

Attachments

  • 20121116_65.JPG
    191.7 KB · Views: 1,077
  • 20121116_64.JPG
    171.7 KB · Views: 1,088
  • 20121116_63.JPG
    181.3 KB · Views: 1,068
  • 20121116_62.JPG
    186.7 KB · Views: 1,040
  • 20121116_61.JPG
    183.8 KB · Views: 1,062
  • 20121116_60.jpg
    102 KB · Views: 1,067
  • 20121116_59.jpg
    101.1 KB · Views: 1,042
Neat project.. might be a good idea to replace the freeze plugs lest they leak after you get it installed.. especially the ones in the bellhousing area... it sure will be easier now than once you get it into it's shiny new home! They may look good but can rust through from the inside.. trust me I've been there!
Nice to see another Dart Sport saved!

Alan
 
Good tip Alan.
All of the frost plugs were changed on the entire engine, the ones in the back of the block were changed after the engine came off the stand and we could get at them. All of the junk in the water passages were cleaned out before the new plugs went in.
We used brass ones BTW!
 
The engine, resurfaced 360 flywheel, bellhousing, clutch, and transmission were bolted together and installed on the K member with the steering box.......
 

Attachments

  • 20121116_119.JPG
    181.2 KB · Views: 1,013
  • 20121116_118.JPG
    166.7 KB · Views: 1,072
  • 20121116_117.JPG
    191.1 KB · Views: 1,033
  • 20121116_110.JPG
    143.6 KB · Views: 1,021
  • 20121116_109.JPG
    150.8 KB · Views: 1,066
  • 20121116_32.JPG
    167.9 KB · Views: 1,078
  • 20121116_1.jpg
    103.6 KB · Views: 1,025
Next were the exhaust manifolds ('73 340) and into the car the package went.
It took about 20 minutes to lower the car down, align everything and bolt it all up.
That's one of the reasons that i love mopars so much! :cheers:
 

Attachments

  • 20121116_127.JPG
    186.2 KB · Views: 1,046
  • 20121116_126.JPG
    193.3 KB · Views: 1,025
  • 20121116_123.JPG
    187.9 KB · Views: 1,047
  • 20121116_122.JPG
    181 KB · Views: 1,036
Well, the interior is next.
We just cleaned up the interior out of the red '75 Dart Sport and installed it as is, dash and all, the wiring under the dash looked like new. The dash was repainted black and R.J. had a good hardly used black 4 speed carpet kit out of his '71 Demon that we did a little trading for. The package tray was cleaned up and resprayed. The '74 heater box and core was cleaned up and resealed then installed. We cleaned and painted the sport mirrors green and installed them too after making a template off the red parts car where they came from.
The window regulator was shot in the passenger's door, so the one out of the '75 went in. All of the window channels and rollers were cleaned up and lubed. The steering column was cleaned up and painted then installed.
We used a new firewall seal kit on the car which was great to replace all of the worn out and weathered wiper seals and foam gaskets.
We used all of the seat belts etc. out of the '75 red parts car because they were a lot better condition wise.
The shifter was cleaned up and installed along with the pedal assembly out of the '75 red parts car.
 

Attachments

  • 20121116_217.JPG
    171.7 KB · Views: 1,014
  • 20121116_224.JPG
    170.6 KB · Views: 1,007
  • 20121116_223.JPG
    155 KB · Views: 1,027
  • 20121116_221.JPG
    152.7 KB · Views: 1,077
  • 20121116_219.JPG
    165.3 KB · Views: 1,049
  • 20121116_218.JPG
    163.4 KB · Views: 1,057
  • 20121116_214.JPG
    144.1 KB · Views: 1,024
  • 20121116_212.JPG
    141.2 KB · Views: 1,044
  • 20121116_200.JPG
    196.5 KB · Views: 1,044
  • 20121116_220.JPG
    163.9 KB · Views: 1,020
It's lookin' real good. Are you sure you want to keep those mirrors on there? I might have a buyer lined up if not! :pl: :D
 
gdrill said:
It's lookin' real good. Are you sure you want to keep those mirrors on there? I might have a buyer lined up if not! :pl: :D
Click to expand...

Sorry,
I already drilled the holes, there's no turning back now.
You should have said something to me a little while ago, i just used them because i couldn't find a set off of a honda for cheap. :D
 
On second thought George, i might trade them for a chromed up A body 8 3/4 housing and axles. Know of any kicking around?
 
Great thread. How long are A body axles? I have 2 that should be B body axles
 
You must log in or register to reply here.
-

Back
Top