OzyDuster74 full rebuild and hemi conversion!!

-
So all the chassis connectors and torque boxes all modded and perfect fit. So got one of my carpenters to swing past and knock up the stands to sit car on whilst all gets welded in. As i only have a two post hoist dont want to risk welding in whilst car sags on hoist.
Its all nailed and batton screwed together it isn't going anywhere especially given car is basically a shell
If it looks stupid and works is it stupid haha.
I have left my run late but was wanting to get the underside sprayed by xmas........ I hope to pick up the 6.4 in next day or so and drop it off at engine builders shop. Basically i want 550-600hp send me the bill
IMG_4381.JPG
IMG_4385.JPG
 
mygasser said:
that timber frame is ideal to paint the floors too as the lift arms can be swung out of the way.
neil.
Click to expand...
Yep after i did this i realised it had a few advantages!! Thankfully my carpenters are car guys so didnt think i was completely crazy doing this
 
you do what you have to do sometimes. i had to do inner and outer rockers/sills on a mk2 zephyr so propped one side on extended stands while the other side was still on the lift arms. you can see i removed the arms from the lift on the side i was working on. it was the best way i could think of to get good side access with my 2 post lift.
neil.
1731943809849.png
 
So this happened got one of the final pieces of the puzzle. 6.4 from a 2014 SRT 300 with all the accessories. Was running with slight tick, not fussed as will go straight to my engine builder. Who will have simple instruction of i want 550-600hp call me when its done lol
Was a good buy as got it for 6k usually more up around 10k here. Parts a little more expensive down here in Australia haha
IMG_4408.JPG
 
Ozyduster said:
So this happened got one of the final pieces of the puzzle. 6.4 from a 2014 SRT 300 with all the accessories. Was running with slight tick, not fussed as will go straight to my engine builder. Who will have simple instruction of i want 550-600hp call me when its done lol
Was a good buy as got it for 6k usually more up around 10k here. Parts a little more expensive down here in Australia haha
View attachment 1716329358
Click to expand...
Very nice! the 6.4 is the main engine I would consider doing a new hemi swap for. Those things are beasts in cars that weigh twice what an Abody does haha. Should be a lot of fun!
 
Your engine guy should have an easy time with your 6.4. You can sneeze and get that power out of them.
 
408 swinger said:
Your engine guy should have an easy time with your 6.4. You can sneeze and get that power out of them.
Click to expand...
Yep i think 550-600 hp in the little ABody should still be decent on the st and pretty good down the strip. Building it to cruise with my two little boys who car nuts and maybe put it down the track a couple times.
 
Ozyduster said:
Yep i think 550-600 hp in the little ABody should still be decent on the st and pretty good down the strip. Building it to cruise with my two little boys who car nuts and maybe put it down the track a couple times.
Click to expand...
Nice! That will definitely be something they remember!
 
After watching all the recent install posts not looking forward to shoe horning the 6.4 into the bay as looks like the Holley kit is super tight.
Do you fit the motor and pipes same time
Can you fit with column and power steering in place?
 
Ozyduster said:
After watching all the recent install posts not looking forward to shoe horning the 6.4 into the bay as looks like the Holley kit is super tight.
Do you fit the motor and pipes same time
Can you fit with column and power steering in place?
Click to expand...

Definitely tight, but I do feel like it all fits. It's not as easy to service things as an LA, but it's the nature of the beast I guess. The only way I see to fix some of those issues is a COC kit and I don't have the funds for that.

Holley's instructions say the DS header has to be bolted up before dropping the motor in. Steering box has to be installed but no column as the steering shaft is captured by the headers so it has to be installed afterwards.

Make sure you do the dipstick while you are fitting the header, I know I can't get mine in with the motor installed and I'm not sure it can be done with the header bolted up either.

Make sure your mounts slip into the saddles on the k-frame. Easiest to do it when they are loose rather than with the motor hanging above you.
 
DionR said:
Definitely tight, but I do feel like it all fits. It's not as easy to service things as an LA, but it's the nature of the beast I guess. The only way I see to fix some of those issues is a COC kit and I don't have the funds for that.

Holley's instructions say the DS header has to be bolted up before dropping the motor in. Steering box has to be installed but no column as the steering shaft is captured by the headers so it has to be installed afterwards.

Make sure you do the dipstick while you are fitting the header, I know I can't get mine in with the motor installed and I'm not sure it can be done with the header bolted up either.

Make sure your mounts slip into the saddles on the k-frame. Easiest to do it when they are loose rather than with the motor hanging above you.
Click to expand...
Ok that makes sense, yep defiantly deleting as much stuff out of the bay as i can to save on space. Thank god i have a hoist etc as feel its going to be a frustrating fit, ill do it twice as once before painting bay etc
 
Oz - For “final” assembly I checked the fit for my engine, transmission, steering box, dipstick tube, starter and exhaust for my 440 on my k-frame sitting on blocks on the garage floor. I did not need to do exhaust and steering box when I put it in the car the last time, but just as easily could have. I then set it on a dolly and rolled it under the car. Then, lowered the car down onto the assembly. No lift, no hoist. Just jack, jackstands and two furniture dollys.

My son and I did this four times when it was at the body shop so we could have them modify the hood for clearance, fabricate the transmission tunnel for the six speed and etcetera. Fortunately the body shop owner was a good friend and he let us work on the car on Saturdays. I am a former shop foreman ASE Master Tech, so he trusted me in his shop. I brought my own air tools, wrenches, sockets. I even helped him and his guys out on a few things. Doing this work is very easy when you have a lift. The dolly we had access to at the body shop was about 3’ high. My then 10 year old son could install or remove the engine assembly in about half an hour and all I did was operate the lift and make sure he didn’t get in to trouble. Pictures below from when I was assembling it at home, and from the last time I had my son remove the assembly at the body shop.

Key to this is knowing how the weight shifts and making sure you have the lift positioned so when the weight shifts it doesn’t cause a problem. We used safety stands and tested each time we added or removed weight of the drivetrain.

DSC06523.JPG
DSC06524.JPG
DSC06525.JPG
DSC06526.JPG
DSC06527.JPG
DSC06528.JPG
DSC06529.JPG
DSC03195.JPG
DSC03196.JPG
DSC03198.JPG
 
Last edited:
mosleyme said:
Oz - For “final” assembly I checked the fit for my engine, transmission, steering box, dipstick tube, starter and exhaust for my 440 on my k-frame sitting on blocks on the garage floor. I did not need to do exhaust and steering box when I put it in the car the last time, but just as easily could have. I then set it on a dolly and rolled it under the car. Then, lowered the car down onto the assembly. No lift, no hoist. Just jack, jackstands and two furniture dollys.

My son and I did this four times when it was at the body shop so we could have them modify the hood for clearance, fabricate the transmission tunnel for the six speed and etcetera. Fortunately the body shop owner was a good friend and he let us work on the car on Saturdays. I am a former shop foreman ASE Master Tech, so he trusted me in his shop. I brought my own air tools, wrenches, sockets. I even helped him and his guys out on a few things. Doing this work is very easy when you have a lift. The dolly we had access to at the body shop was about 3’ high. My then 10 year old son could install or remove the engine assembly in about half an hour and all I did was operate the lift and make sure he didn’t get in to trouble. Pictures below from when I was assembling it at home, and from the last time I had my son remove the assembly at the body shop.

Key to this is knowing how the weight shifts and making sure you have the lift positioned so when the weight shifts it doesn’t cause a problem. We used safety stands and tested each time we added or removed weight of the drivetrain.

View attachment 1716330975View attachment 1716330977View attachment 1716330979View attachment 1716330980View attachment 1716330981View attachment 1716330982View attachment 1716330983View attachment 1716330984View attachment 1716330985View attachment 1716330986
Click to expand...
Love it mate, and yep a few of my mates have said just drop it in and out via the K frame. As sounds like a headfk to go up and out etc Got a handfull of mates with valiant which are similar all happy to throw down when i need. I am a holden man (gm owned australian brand) most of my car buddies Holden guys but a motor is a motor. So plenty of hands ready to help, my factory backs on to a mates factory who is a wiring guru as thats the bit that scares me most haha
 
You must log in or register to reply here.
-

Back
Top