Dissembling this 750 double pumper. I bought it cheap with it well cleaned and a new kit installed. It’s supposed to be ready to run but you know how that goes !
What Are You Doing To/With Your Car Today?
- Thread starter MobileCustoms
- Start date
-
72Dart6pack
Harder Better Faster Stronger.
Making progress today. Intake is just something to fill the void for a bit.
Mouse action
Well-Known Member
Congratulations.
CarfinaticII
Under Construction
Got my firewall striped and epoxied. Got some pieces from AMD and rebuilt the cowl to inner fender pieces. Welded in the other piece that holds the fender on at the top as mine was rotted out. Sanded down the area behind the splash shield and epoxied it. Progress is slow but it’s gettin there.
Cleaning up some more carbs:
318 Roller Engine Build from last Summer, in the Truck now.
318 Roller Engine Build from last Summer, in the Truck now.
1969cuda
Well-Known Member
A light detail job as I get it ready for Kool April car Show/Drags on Wednesday.
Drug store run for pop, milk, bread and most importantly chocolate chip cookies.. lol Short cruise around town this round with us under full stay at home orders and still not sure on the OPP's stance on harassing us about where we're going..
340wedge
Well-Known Member
- Joined
- Nov 14, 2004
- Messages
- 1,158
- Reaction score
- 847
Just tell them you need to exercise the Musclecar's legs. It is true, they get issues by sitting too long!
Still putting my Engine together. My OCD thought those freeze plugs needed to be polished.
View attachment 1715724473
View attachment 1715724474
View attachment 1715724475
Ok....that's a bit much. ....bad ***, but a bit much!
Jeff
Total of 5 Carbs broke down and cleaned in the Ultra Sonic Cleaner today, dry and ready for assembly tomorrow.
The last one was the "Old School"
The last one was the "Old School"
Turns out you guys were spot on , flipped the center link around and put the tie rod towards the front of the car PLENTY of clearance now. Thanks!!! Proceeded to install QA1 shocks and the rotors ,calipers , brake hoses and lines from the Pirate Jacks kit. Everything went on smoothly.
Take Note: Those are the "New" 4" bolt pattern drilled and slotted rotors. Don't know if anyone else offers them ?
Take Note: Those are the "New" 4" bolt pattern drilled and slotted rotors. Don't know if anyone else offers them ?
Last edited:
racerhog
RacerHog likes his Mopars
Jeff, Are you registered and going to Corn feed Car Show this upcoming weekend in Chino?
Corn Feed Run Car Show & Cruise
Swapping out engine and third member, going with green axle bearings. And exchanging the rear yoke for the smaller one with a new nut and seal. Should keep me busy for a week or two..maybe three... lol
@racerhog
Heck yes......rolled over from last year's cancellation!
I'll be there super early to get my spot in the shade!
Jeff
Red's '72 Dart
Well-Known Member
Got my instrument cluster installed.
skep419
5.9 Magnum 4 speed afficionado
Installed my “Green” bearings, pretty sure I lowered the worlds temperature by 2%. LOL
Trans pan , filter and gasket then fluid, shifter linkage will take some time. My to do list today if it warms up out of the 33 degrees I woke up to this morning
Working through the carbs:
There is an antique early '67 AFB coming up for completion too. Came off of a 67 383 4 bbl 10:1 cr factory original engine.
There is an antique early '67 AFB coming up for completion too. Came off of a 67 383 4 bbl 10:1 cr factory original engine.
This stuff is stinky!!
72Dart6pack
Harder Better Faster Stronger.
So does that first photo make it a 20 Pack? I'm only 14 short.
So does that first photo make it a 20 Pack? I'm only 14 short.
Had to think about that for a while ???
Five x 4 Barrels = 20 Pack,
You have Three x 2 Barrels = Six Pack
Now I get it, lol . .
☆☆☆
skep419
5.9 Magnum 4 speed afficionado
So does that first photo make it a 20 Pack? I'm only 14 short.
-
