Search results for query: *

nothing it was 9 degrees for a high temp everything is covered in snow and I have yet to find a heater big enough to warm my backyard since i don't have a garage unless you count the trees in which case the roof fell off my garage in oct

lol this reminds me of the time i was in advance a few years ago and this guy in a chevelle was trying to order parts for it the guy at the counter asked him what engine he had and the reply was 'rat motor" . the parts guy said i need the size guy says 396 rat motor . Im unfortunately right...

its a cool car but like some others have said a mopar engine would be better in it. Im not closed minded because I own other old cars besides mopar but i grew up mostly around mopars and just prefer them over others. i like a lot of the older cars from chevy ,ford and chrysler. mopar and ford...

a 318 is chryslers definition of light ?!!! id hate to see what the original A's weighed then because a bare 318 block weighs almost as much as a chebby 350 fully assembled does . i carried both up 2 flights of stairs in college so i know this one from hard earned experience

my daily driver is a 2010 jeep liberty but before that it was an 89 buick park ave i had some issues with the buick then hit bambi with it so it went to the junkyard . during the many breakdowns with the buick my 72 galaxie served as backup dd and did well as long as it wasn't snowing almost...

I'd rather be blowing peoples doors off in what looks like junk than pushing something that looks like a show car. That being said I would repair or replace floor pans and anything rusted on the underside or at the very least make sure I cleaned up the underside as far as rust removal goes...

from what I've seen klein went to china as well I was on the verge of buying some of their tools last week till i seen made in china on the screwdrivers and wrenches

make sure the a/c condenser isnt filled up with bugs and debris and the fins arent all smashed on it especially since its in front of the rad if it gets clogged up with stuff it will block air going to the rad

finally someone understands lmao

That will buff right out maybe a little body filler n some sanding shell be good as new

Holy crap . That's funny

gotta love red green

more than likely the gas smell in the oil is due to running to rich or a fuel pump starting to fail and dumping gas into the oil but could also be low compression because of worn rings . as for having to dump gas down the carb to get it running you probably have a leaking carb that is draining...

Where was she when I got my cdl ? I got cheated I think

thanks for the tip davebonds ive been wondering what i was going with mine as well . thanks to the op for asking also

they say beauty is in the eye of the beer holder and someone must have had more than a few to many to do that to the poor car and think it looked cool or even good

i was wondering that too . are they stock heads that had work done ? or are they aluminum heads ,if so what brand and have they been worked over ? i never seen any mention of that at all .

did anyone else look at the car and location and automatically start singing the jan and dean song little old lady from pasadena ?

another random thought : studs have to be torqued properly , im wondering if they were just screwed in till they stop and then when he tightened the nuts down and fired it the combo of the vibration heat and expansion of the parts caused them to loosen enough that it pulled water into the...

nothing! you better send it to postage paid right away so i can put it to use lol. seriously though it depends on if someone really needs it or not i have one that was completely gone through bored 30 over and has $2500 in parts in it that i built for someone and they screwed me on it . sold the...

just thinking here but you might want to pressure test the cooling system before you fire it up tomorrow after the heads are torqued down . do it with the spark plugs out so if its still leaking into the engine you know before it hydrolocks and causes expensive damage . If you dont have a...

i say the rapid transit plate but neither will keep the stupid people from asking what year your nova is . If i had a penny for every time i heard that question i could fill up 2 tube socks enough to possibly knock them completely senseless .

anyone else notice that the ring teeth look really worn closer to the tips ? im thinking his problem might go away with a new ring gear . or he could try shimming just one side of the starter to bring the gears closer together since it looks like the teeth are not catching as much as they...

if i wasnt broke right now i would grab that carb

compression should be a minimum of 70 psi with no more than 10-20%variation between all cylinders. i may be a little off on specs but but if all cyl have atleast 70 it should have enough compression to fire and run

a buddy of mine whos grandpa owns a quarry has 3 slants 1 runs a rock crusher 1 runs the conveyer and another in an old 60s single axle dump truck . all 3 of them early to mid sixties and never been apart .lol

he must know a few of my exes but still be in denial about the personality

prayers sent sorry to hear about your loss

x2 definetly research it i have seen and heard alot of of horror stories about nursing homes make sure you find a good one that will treat your mother well. although i havent had to make that descision yet i can understand what your going through. just take comfort in knowing that you are doing...

sorry for your loss prayers sent for you and all that knew him .