Search results for query: *

My combo I run in my d150. 360 magnum, .030 forged flat tops with 2 valve reliefs. .001 in the hole. .039 headgasket. EQ heads worked by brian hafliger. Comp mutha thumper cam installed 4* retarded. Mopar m1 single plane. Holley hp series 750. 15/8 hedmans. 727 10" 3600 converter. 3.55's. I...

I still want to know exactly what a "j" converter is Lol

Still available? How old?

Also, i mocked up the engine in the 4 corners. My deck height was off from end to end. I wanted to end up with a .040 squish, so my block was decked to put the pistons at .01 down. I used a .039 compressed felpro headgasket. After talking with brian, and to keep my engine pump 93 friendly, it...

I built a clone of the sledgehammer engine with the following exceptions. I used wiseco piston kit( pts527a3) and scat rods(2-icr26123-2124). Got a really good buy on both. And used my existing m1 single plane. Engine is in my 85 d150 and i couldnt be happier. I did have my assembly balanced...

They make forward pattern also. Butvas others have said, try a bunch of diffrent ones and the track or friends or something. Make model of vehicle dont matter when ya looking for a certain feel

I run a reverse valve body, and of all of tried through the years, itvis by far been the easiest to operate. My 13yo daughter can drive it. Its that easy, never misses and has hard stops

I prefer a Hurst 1/4 stick

I dont imagine that cam has alot of manifold vaccum. Guessing initial timing should be 16 degrees or so( every engine is different) i would think it would run better if total timing was in by 2800-3000.. and possibly more converter

Yes swap those 2. Vacuum canister on distributor

good deal, glad u have it figured out

If the intermediate shaft was installed correctly, by the look of the vcan, youve got alot of timing in it. And as was said, move the 2 large vaccum lines. Pcv should be at carb, booster should be full manifold vaccum. Im not a big fan of edelbrock carbs, but thats just me. A 700 or 750 holley...

So what was the problem?

You can, once you have 0, and #1 pointing at the correct pole on the cap. If you have timing tape, or marked your balancer, if you want to rotate the motor to say 12 btdc, roll the motor to that mark, move the distributor to line back up on the cap, and lock it down. May not be exact, but will...

This is what i would do, pull #1 sparkplug, put your finger over the hole and bump the starter till you feel compression. The roll the engine over by hand to zero. Pull the intermediate shaft back out and reinstall it pointing toward the forward dr side intake bolt, install the distributor...

Sometimes folks will set the cam 2-4 degrees retarded to bleed off some cylinder pressure, especially when using high static compression pistons with an iron head, in an effort to be able to use pump high test fuel(91-93octane)

Would this be a 904 issue, or does the block need to ground when using a 727? Would rather grind the block now when its on the stand.

Have located a set thanks

Thanks for the heads up!

Searching for magnum black wrinkle finish valve covers. Thanks in advance

Next if deal falls thru

Im currently building a close copy of brians mopar muscle motor. I used a wiesco piston(.010 shorter ch) and decked the block accordingly. After talking with my machinist about the cost of reconditioning my tired,abused factory rods, i chose a new set of scat i beams. Using the same thumper...

Why have i never seen this car around town? Not many of us mopar guys here in florence

Went with the wiesco. 405 delivered from kjperformance. Probably wont be shootin very often, but ill keep the tuneup safe when i do. Thanks for the help

hey now! I race 2 strokes also!

I asked the question mainly due to the piston material of each. Icon is a 2618, wiesco 4032. Had been shooting 125 on the factory hypers for a long time. Upon teardown had one with the top land broken, and most of the top compression rings broken, truck was still running the same numbers but...

Which to use? Might see a 125 shot every now and again. This would be a flat top/ 2 vr in a 360mag

3.8 or 4.2 kickdown band lever. Thanks in advance