Search results for query: *

RIP John, you will definitely be missed.

a long 1/4-20 bolt bent in the right direction works for me.

I just bought a spare to keep in my trunk from amazon autoplicity and it was USA TI.

TI Automotive made in USA Pick your part number and then you can order on Amazon or another vendor TI Automotive – Fuel Your Adrenaline

My bad, I read about it 40+ years ago and my memory recall has gone to crap as the years go on.

Small block progression info Sorting Out: Chrysler’s 238, 318, 360 Engines, Doug Anderson, Automotive Rebuilder, April 2000

4 oz to 10 gallons for fuel. MM was developed for radial aircraft engines in WW2 era. Google it and you can find an article of the development, it's a good read. I would run what you have and not worry about it. You may have induction hardened and not even know it. The auto industry knew...

By the time I narrowed a dana, bought gun drilled axles from Moser and installed rear disc brake setup I was within 10 lbs of the 8.75. I got tired of fixing the 8.75 and decided to go dana. Have not worked on the rear axle since except for lube change. The axles from Moser came with a 10 year...

You may be able to purchase or if you are creative make some angled baseplate spacers to level the carbs. Lots of marine inboard motors ran angled spacers.

yes

Definitely looking forward to cooler, drier air! I ran my car Friday night @2700 ft DA, 88% humidity.

A perfect day for sure.

In post one the ring gear is off. Install the carrier without the ring gear installed and set the carrier bearing preload. Mount up a dial indicator and check the runout. I believe max is .004 but refer to the FSM. If it's out of spec it screws up the Backlash when you check that. You tube has...

check the ring gear mounting surface runout with a dial indicator and if it's good I'd run it.

6&12 you are #6 TDC

You need to figure out what circuit you are running on when you feel the miss. are the primaries flowing or are you still on the idle/t slot circuit?

Yep, my money will go to someone else in the future.

I ran into this recently with Hughes 1.6 aluminum rockers. I was missing out on over .045 lift with the correct length pushrod and finally saw the difference of the adjuster location to the centerline off the rocker shaft on half of the rockers I received. Look over your rockers and use a...

Inboard edge of the frame rail to output shaft centerline. You can also check pinion centerline the same way.

You can solder some of those .028 shut. A tiny bit of flux cleaner and you will have no problem soldering shut from the bottom.

Try another gauge to verify.

Since you have an MSD adjustable timing box set the timing to 25* initial timing with VA disconnected. +-7* adjustment will allow you to figure out the best idle timing. Run the engine up to full operating temp with the hood closed and turn the engine off. Wait 5 minutes and allow the engine to...

I run an OEM electronic that I've recurved with an analog 6al. The mallory style mopar that summit sells are easy to setup.

One flat may do the trick. Middle of the sight glass has always been best for me. It looks like the PJ comes in at 3400 by your readings.

I've had mine read pig rich when the engine was starving for fuel. Heat soaked motor and fuel boiling off in the fuel pump. Car would barely run at idle with fuel bowls empty. Acted like the motor was drowning in fuel until I saw the fuel level.

1) the middle gave me the most stable and flat fuel curve at cruise and WOT 2) see 1 Think of the emulsion as a means to tame the fuel flow to behave in a stable, predictable manner. Now add or decrease jetting to run the afr the combo likes the best.

I run a 360 [email protected] cam, sealed hood scoop, return fuel system and 750DP Demon. I drive this car on 93 octane pump gas 50 miles to run at the track. The tune I run is 14.0 afr cruise and 12.3-4 wot 1/4 mile. 71/85 jetting MAB .028 IAB .067 front .070 rear IFR .032 bottom position T slot...

It's Ford tranny linkage. Take it off and use it with the standard mopar bracket.

I run a carb so this may not apply. I briefly ran that intake on my 360 with a square flange plate, 1" 4 hole HVH Super sucker and a 750dp carb. 3, 6, 7 cylinders were rich. I swapped to a Victor 340 square flange intake and 3 & 7 are rich. Car runs great with either manifold but I'd like to...

I would also make sure the valve guides aren't to tight on that cylinder since you had another failure.