Search results for query: *

any one looking for a 68 model A-833 4 speed transmission??? VIN 8B257729? Ben.

looking for original engine for my Dart. Have a warranty replacement block in it now. LM23H0R214912 vin. February, 1970 build date. Thanks, Ben.

looking for a rebuilt or like new A-833 transmission for a 70 Dart. Have a used one, but the case is bad. Would like something that can be bolted in with no problems, Thanks, Ben.

Installed new bulbs and holders into the rally dash on my 70 Dart.....installed the dash back into dash frame, turned on the lights and I seem to only have some dash lights around the speedometer, not the tach or other gauges. All grounds seem to be in place and I can't believe I have that many...

anyone have some lockout linkage for a 70 Dart with a manual transmission? Looking specifically for the adjustable piece of linkage that attaches to the steering column and then to the cross shaft. Would also be interested in a cross shaft although I believe I can adapt the automatic...

Looking for a 70 only manual transmission key lock out linkage. Need the piece that goes from the steering column to the linkage cross shaft. also have a thumbwheel style AM radio in the rally dash. Looking for the rear brace that secures the radio to the lower edge of the dash. 70 Dart jack...

Any body know where you can pick up some of the cloth style sheathing that acts as an anti-rattle on the inside door latch rods? Thanks, Ben.

wtb--70 Dart Swinger hood scoop clips that hold the chrome bezels on the front of each scoop opening. Need 3 or four. first picture is of a sample of what I need. Also need the keyhole clip that holds the 'thumbwheel' style radio in the dash of a 70 Dart with the 'rally dash'. Second and third...

Does any one have either diagrams or photos of the 70 only manual transmission interlock linkage? Would certainly appreciate photos if available. Thanks, Ben.

am looking for a retainer stud that holds a thumbwheel style radio into a Dart with a rally dash. Could also use the 2 larger style nuts that thread onto these retainers also. The first picture shows one installed in the dash in the upper corner. The hole with the slot in the lower right corner...

Am looking for three exterior 'Swinger' emblems for a 70 Dart. I have a couple of the 3 spin variety, but am looking for new or like new 4 pin emblems. Could also use a 'Dart' emblem for the trunk lid in new or like new condition. Please PM. Thanks, Ben.

Looking for some emergency brake parts. Picture is of what I need, but for the drivers' side of the car. The picture is of the parts on the right side. 70 Dart with an 8 3/4 rear with 10x1.75 in. shoes. Any help would be appreciated. Thanks, Ben.

WTB........manual transmission driveshaft for 70 Dart Swinger 340. 8 3/4 rear with the small yoke. Want something that is dent free.....either used needing rebuilding or rebuilt. Thanks, Ben.

looking for a complete jack assembly for a 70 Dart. Thanks, Ben.

am looking for the right side 'A' pillar vinyl top trim. enclosed picture is what I need. Also looking for a knob for the wiper switch on a 70 model Dart with the rally dash. no idea if the standard dash knob is the same or not. Thanks, Ben. still looking for the manual transmission...

Does anybody have any experience with Wizard Cooling radiators? They advertise an aluminum radiator that will fit a 70 Dart 340 engine with a M/T, which includes an aluminum shroud which attaches to the radiator like OEM. Just wondered if anyone has had any experience with one of these as to...

WTB--65-71 Dart V-8 manual transmission dust covers.......I need the inspection cover that attaches to the bottom of the bell housing, as well as the dust shield that extends across the lower front of the bell housing and the starter goes through on the drivers side. Please PM. thanks, Ben.

1970 Dodge Dart Swinger with the 340 engine without A/C. Does this car use a fan with fan clutch or does it use a direct drive fan with a spacer like my 69 Dart did? Any help would be appreciated! Ben.

FOR SALE: A used pair of small block Mopar 'Holley' valve covers. In good condition, presently coated with some kind of crinkle black paint, with other colors underneath. Nothing cracked or wallowed out. Need to be stripped and refinished or possibly sent to the resident 'princess of powder' for...

Looking for a standard transmission flywheel inspection cover and the dust shield the starter goes through. Both parts attach to the bellhousing. Working on a 70 Dart 340 4 speed car. Thanks, Ben.

for sale: left side 'ramcharger' hood scoop. In good condition, has a coat of red oxide primer on it. No cracks or bad stud holes, although only three of the studs are present. Has lots of little scratches, so a coat of filler may be necessary to smooth out surface. Has a chrome bezel that is in...

looking for a new or used 340 six pack air cleaner assembly. (would also be interested in one of the aluminum 'tri power' air cleaners if someone has one available.) Ben. also need a set of full wheel opening moldings in excellent condition for a 70 model Dart coupe. Thanks.

I need some help identifying a swing pedal assembly.......sold to me as an early 70 A body set-up, but it doesn't look quite right. Especially the brake pedal with the funny twist where the pedal pad is. Any help would be appreciated! Ben

looking for some replacement wiper arm bushings for a 70 Dart with a 2 speed wiper. These are the black plastic type. Need three of them. Ben.

Want to buy: 70 Dart floor shift power steering column. will rebuild if necessary. thanks, Ben. ( would be interested in just the upper column parts if available!)

I have a new AAR six pack bolt on hood for a 70-72 Dart Swinger. Have decided to use the stock scooped 340 Swinger hood, as it has been satisfactorily repaired. I paid 750.00 dollars for the AAR hood, which included 125.00 for the shipping. I realize I won't get that for it, but am open to...

I have a right side stock exhaust manifold for a '70 340 engine that has the heat riser valve. Problem is the shaft on the valve has quite a bit of play in it and there is an exhaust leak. Can these valves have the bushing replaced or should they just be removed and a small freeze style plug be...

I have a set of factory hood scoops, that came on my 70 Swinger 340. I believe from the outline of the emblem, they might have originally come from a Super Bee, etc. No cracks, holes or bad studs--black paint has chips. Part no.'s 2949194 and 2949195. Included two nice bezels. Not chrome--have...

70 Dart Swinger 340, auto., no AC. Any recommendations on an aftermarket radiator that looks similar to stock. Really don't want to cut up the core support or drill a bunch of holes. Aluminum would be okay. Thanks, Ben

WTB 70 Dodge Dart non AC heater box. Am looking for a very nice unit without cracks or problems, if possible. Don't need the heater core or blower motor. Unit I'm replacing has part no. 2936864 stenciled on above the fresh air door. Included are a couple of pictures of the unit I'm looking for...