Search results for query: *

Quick question, what doors would be a bolt on for a 72 Demon? 70-72 Duster and 71-72 Demon? Need to find a passenger door...

Hey folks, been absent for quite a while, after some pretty substantial life changes I'm back, just brought my 72 Demon home and anxious to get back to working on it almost 6 years later LOL Quick specs, 72 Demon, was a gold slant 6 car, now a 550hp 440, 727, 8 3/4" rear with 3.91's, 8 point...

Took the Demon out for a little test ride on my street, after 5 years of building she actually moves on her own now LOL here's a couple vids Ryan http://www.youtube.com/watch?v=qN59iw7o7Ms http://www.youtube.com/watch?v=r-1xy9YkgfU

I'm about to retorque the heads on my 440, can it be done without pulling the rocker arms and shafts? REALLY would rather not if I dont have to... Ryan

Maybe someone can rationalize it but, after going and finding a new rear main seal, 2 sets of oil pan gaskets and drinking myself stupid thinking about pulling the motor and dropping the pan etc. to change out the rear main seal, I start it up last night and again today, bring it to operating...

Fired up the Demon and broke in the cam today! She sounds MEAN!!! Now the downside is the rear main seal is pissing oil, but hey atleast I dont have to do it just once LOL....Also the headgasket was leaking steam every 30 seconds or so when the temp was around 220*, finished break in and shut...

Ok can someone give me a step by step rundown on startup/break in procedure? It's been a very long time since I started a new motor for the first time and dont want to forget anything! Motor: .030 over 440, 11.5-1 compression, Eddy heads, MSD 6AL, MP distributor, Comp Extreme Energy cam .509...

I need the plug that plugs into the neutral safety switch on the transmission, mine is SMOKED the 3 round terminals in the plug are gone, no contacts at all left...Anyone have one? I'm ALMOST ready to fire the Demon for the first time, doing all the last minute hookups and this is one of the...

Can any give me a simple wiring diagram to wire an elec fuel pump using a relay? Do I really need a relay? And can I use just a generic 30-40 amp relay? No oil pressure switch for now, just need to get it hooked up so I can start the motor for the first time Ryan

Started installing my Pypes stainless Race Pro exhaust today, great quality so far, I have the mufflers hung, the tailpipes tacked into the mufflers, the X-pipe clamped into position (Leaving that joint unwelded incase I ever need to pull the tranny...All I have left is to make the downpipes and...

Anyone cutting up a car? Looking for sheetmetal patches, need a body floorpans front and rear, a body rear outer wheelhouses, both outer rockers, a body torsion bar crossmember, all going into a 73 Duster...If you have anything let me know, [email protected] or PM Ryan

Looking for a working 2 speed wiper switch and a brake light switch for my 72 Demon, email or pm [email protected] I'll buy them new if someone can tell me where, Yearone doesnt list either... Ryan

I'm installing my wiring harness, doing the connections at the column right now, stock column-Ron Francis Wiring kit, on the factory diagram there's 2 ignition wires, anyone know which is which? They're labeled "Ignition 1" and "Ignition 2"...I assume one would have power with key in start and...

I desperately need a portion of under dash wiring harness, installing my aftermarket harness and I need to splice in a few stock connectors, namely I need the harness side of the column plugs with enough wire to cut and splice, same with the plugs for the heater controls, and dimmer switch...

Ok I'm using a mini starter on the 440 in the Demon, it's the same type used on the Dakota's etc but aftermarket, and a Ron Francis harness, do I still need a starter relay and starter solenoid? Or is it built into the starter?...Hey I said it was a dumb question ...Wiring definately isnt my...

Looking at new stereos for my Ram, Not looking for super expensive, $150 or so, maybe a little more, but I want something with a front input for my MP3 player, rear inputs for my amp and subs, but also I want to hook up my new Satellite receiver to it rather than using the FM transmitter, is...

I'm in need for a patch piece for a Demon Tail panel, I need the area in the red box in the pic, [email protected] if you have one! Ryan

Ok can someone tell me how the lock/latch comes out of the glovebox door? I've taken the screws out of the back but I'm going nuts trying to get it out of the door! Ryan

Anyone have any pics of the routing of the brake lines from the master cylinder to the prop. valve? and out of the prop. valve? I could use a couple pics of that whole area if anyone has them...Running all my lines and I want them to look somewhat factory ....thanks! Ryan

Hey guys, been lurking here for quite a while, see alot of familiar faces from BigBlockDart.com, for those that dont know me, My name is Ryan and I'm addicted to Mopars...There I said it...They say admitting a problem is the first step....I'm building a 72 Demon, bought it as a /6 904 car from...