Search results for query: *

What will it take to mount my small block 833 to a 400 block I know bell housing need swapped but what as far as clutch/flywheel and z bar setup.

Ok I just have put a new clutch/throw out bearing in the car. It had been in there about 150 miles. Now when you have the clutch press and tap the gas the bearing starts chattering and you release the clutch it stops and press the clutch again no noise till you tap the gas. It also chatters when...

Is there a right way to put a speedo gear in I took mine out to check it when we changed the clutch.I put it back in but the speedometer is not working and theres a small leak from the seal.Also is there a way to pull the gear out without pouring the oil out.

Ok pulled the trans to put a new clutch in and the input shaft has alot of slop.So I need a new bearing. It is a 71 model 833 non overdrive will this work? http://www.brewersperformance.com/proddetail.asp?prod=B307M

Ok so on my 73 duster 360 4 speed. McLeod 10.5 diaphragm clutch the clutch pedal gets sticky when you press it only after you drive if and get it good and hot.

If I use this locker what all do I need and have to do you put it in my duster 8 3/4 rear http://www.doctordiff.com/8-3-4-eaton-truetrac-differential.html

When I press my clutch my z bar moves toward the drive side about 1/2 inches what will cause it to do this

Ok so my clutch pedal was sticking when coming up so I changed the bushing in the z-bar now it is smoother coming up but pretty sticky when pressing down. What would cause this?

When I press the clutch pedal the z bar moves slightly to the left what would make it do this. 71 833 trans and engine in a 73 duster (was an auto car)

Is the starter the same for a auto and a manual trans 360/904 to a 360/833

Ok so I finely go most of the part t do a 4 speed swap so I guess I will do a thread. What I have 71 833 trans Pedal setup form 71 340 Duster Old Clutch and Press Plate (Going to be rebuilt) Shiter band new rebuilt from yearone Shifter Linkges BellHousing Cluch Fork Dust Shild Floor Hump Z...

What speedo gear do I need for my 73 duster 4 speed swap 28in tire 3.55 gear

Well I got the guy to a price I would pay and bought it. 833 trans non-O/D from Bellhousing Pedals Clutch Fork Flywheel Old used clutch Brand new rebuild shifter from yearone Shifter linkages Floor hump All from a 71 Duster Were can I get a new rear seal a new side cover gasket Will the...

Ok so I have been talking to a guy about a 4 speed but cant figure it out The guy says it a 4 speed but I think its a overdrive The number on the side c 99386 Is there a table with numbers I can show him

Going to look at a 4 speed with a 340 flywheel can I get a 340 flywheel to fit or 360 of do I need a 360 flywheel.When I did the engine swap in my duster I bought the plate to run a 318 tq converter on the 360 with a 904 trans.

Ok so I have been saving and am getting close to getting a 4 speed.My dad keeps saying manual cars have a better feel the left the front end and make it feel more powerful.The only manual car I drive is a old nissan truck with a 4 speed but it has maybe 50hp on a good day.So dose a 4 speed...

Ok so I bought a 833 4 speed today C99129 PP8330198 From what I have found its out of a B or C body mopar. Its a iron case non overdrive spins very smooth.Looks good inside to. This is a longtail tranny and I know I will have to make a bracket to fit in my 1973 Plymouth Duster.The car is...

I am going to look a a 833 tranny how do I tell the gear ratio on the tranny.And more info about it.

Ok so I so I am looking to put a 4 speed in when I do my motor swap. I was looking would a 833 4 speed work in a 73 duster the guy says its for a smallblock but its a early model longtail