you didn't do your research, did you. you might check out Molnar
426 stroker dropped in scamp
- Thread starter 426ohyeah
- Start date
-
you didn't do your research, did you. you might check out Molnar
j par
Well-hung Member
I'm going to have to unwatch this thread it is way above my paygrade.. this is just completely ridiculous BS... I'm done wasting my time... This yr all over again..
Jpar out..
Jpar out..
WHY NOT , MY 360/426 IS WORKING WELL , of course not as great as yours
yellow rose
Overnight Sensation
.060 over 360 with a 4.125 stroke. It’s actually 428 CID but no one follows the rule to round up anything over nominal.
justinp61
Well-Known Member
- Joined
- May 15, 2009
- Messages
- 3,146
- Reaction score
- 4,149
There a couple GM guys here that used to run big, big blocks. Anytime anyone would ask they'd say a little over 500". I eventually found out that one was 599 and the other was 580 something. They both knew my old engine was a 408 so when the 434 was finished they were questioning me about it and wanted to know how big it was. I told them a little over 400". I just rounded it down. LOL
Last edited:
Wives tend to do that with prices. If its "only $500" , that means it is $599.99,.................. after mail in rebate....
yellow rose
Overnight Sensation
True dat. I round down though. $599.99 is $375.00 on sale. She never looks. Well, not often. Then I just grab my sleeping bag and head to the motorhome for a few days and it all blows over.
426ohyeah
Old School 340 "Mad Scientist"
That's alot of block milling. 4.00 stroke plenty.
426ohyeah
Old School 340 "Mad Scientist"
Yep your fault buddy if your doggone 360 is blowing up in the driveway. And guess what??? You are a simpleton that cant do it correctly. May I suggest you find an engine builder and use him. And you can take your big red X and shove it where the sun don’t shine.
Sim-pull-ton
j par
Well-hung Member
Hey the brothers gave me a red X on my last post LOL...
Jpar "back out"...
the OP likes to disagree with facts.
His R+D lacks the research. lol
His R+D lacks the research. lol
the OP likes to disagree with facts.
His R+D lacks the research. lol
He is a meatball. I doubt if he’s capable of cooking up anything. I’m out. Lol
NC Engine Builder
Grumpy Old Man
- Joined
- Oct 10, 2008
- Messages
- 6,449
- Reaction score
- 9,262
Dude posts a picture stolen from the internet showing something that looks like a ford head, says hes busy "step milling it" and then claims hes I guess milling his own cylinder head out of a chunk of billet.... complete and total bullshit thread
fratzog lover
Well-Known Member
Did I see this in the kitchen next to the microwave cart?
yellow rose
Overnight Sensation
justinp61
Well-Known Member
- Joined
- May 15, 2009
- Messages
- 3,146
- Reaction score
- 4,149
You're in over your head and don't know it. Ignorance is bliss. LOL
j par
Well-hung Member
I pushed the unwatch button for this thread but I still keep getting notices for it? Will everybody please stop posting LOL..
My 68 340 block had to be bored .060 over, Dropped a valve in that eng, and it when threw the cyl wall. No way in hell i could have been bored .020. more! There wasn't .020 of cyl wall left.
SSG_Karg
Enhanced member
Ohhhh no you don’t! You threw the match on this dumpster fire! You’re stuck in this for the duration now buddy......
j par
Well-hung Member
Disagreed, Big red X... (Actually it's a little X but when gurus get it they can't see anything but something huge and disagreeing)
Look at Pittsburgh's last comment and the only one that's agreed with you...
It's only the fact that meetball for whatever reason zeroed in on me when everybody else was making comments worse...
j par
Well-hung Member
It's not my red X damn it and it's not big..Jpar you may not be able to keep ownership of the RED X much longer with all these red X's flying about here.
LOL...
...Well it's big but that's a different subject...
... -
