Search results for query: *

For those of you who use PTFE hose for fuel line, which type did you go with, conductive or non-conductive? Where did you purchase your hose and hose ends? And how happy are you with them. I thought all PTFE hose was created equal and just came across an article about the potential dangers of...

I noticed my '66 Dart FSM doesn't specify what tail lamp bulbs to use for the single filament bulbs in the deck lid. It calls for 1034 for the tail, stop, and turn bulb, but nothing for the corresponding deck lid tail lamp bulb. Do you guys happen to know which single filament bulb will...

Does anyone have a photo of where the factory resting position is for an early A-body door handle and window crank (w/ window up)? Something like this (photo below) would be great. Thank you.

I'm getting my '66 Dart GT back together and I'm hoping someone can show me how far up the A-pillar the door weatherstrip goes. Does it end right where the vent window stops? A photo would be really appreciated. I'd imagine Valiant hardtops and early barracudas would be the same too. Thank you!

Have any of you had the little ledge that holds up a headliner listing wire/bow bend or break off? This is an early Dart HT, so I'm unsure if '67-'71 Darts have a bow in this location. I got just about done with the installation of the headliner in my '66 Dart when I noticed that one end of the...

Can you guys confirm that the rear view mirror in my '66 Dart is upside down? I've seen them both ways, but this way looks off in my opinion. It's supposed to be wider at the bottom, right?

Big block cast iron passenger side exhaust manifold - casting number: 3751074. $20 (plus shipping from 95691). Or if you pick it up, you can have it for free. I just hate throwing parts away. It's missing the heat control valve, but otherwise appears to be in fair enough shape with no...

I came across this on the tube. Which of you boneheads is it?? Let's see more of this early Barracuda!

For those who have installed a Holley stealth sniper efi, what air cleaner base did you use? I realize they're modeled to look like a 4150 Holley carb, but when I talked to Holley tech, they said the stealth efi unit is a bit longer than a regular 4150 carb and may interfere with an air cleaner...

Are there any decent alternatives to bright dip anodizing aluminum trim? For instance, could the trim be polished (after stripping the original anodizing) then coated with say a clear powdercoat or clear anodizing? Is there another clear coating that could work? I'm straightening and...

Like new Tekton 1/2" drive torque wrench. 25-250 ft-lbs. Part number 24340. I've only used this one once but I'm getting rid of tools I have more than two of to prepare for a move. Located in West Sacramento - $30 plus shipping or local pick up. PM me for a shipping quote.

Do any of you guys run Billet Specialties Street Lite wheels? If so, could you post up a photo? I'm considering a set for my '66 Dart. I'm thinking polished version would go better on my white '66 than the black version, but I'm kind of on the fence.

Used small block pushrods. These are all straight, have been cleaned up, and the oiling holes are cleaned out. They're out of a '89 roller cam LA 360. Length is "about" 6.750 inches. I don't have a pair of 12" vernier calipers, so I can't get a precise measurement (refer to photos). Price is...

For those of you who have installed a bow-style headliner in one of these old Mopars, how much of the bow channel on the new headliner did you trim? In other words, how much of the bow do you leave hanging out before installing?

I'm looking for a twin post side mirror (#2255521) for an early Dart. Must be in good shape with a tight ball joint and I'd need it shipped to 95691. Let me know if you've got one laying around. Thank you!

Are there any sealed beam headlights on the market that are worth a ****? I know the GE nighthawks were decent until they outsourced to China, but are there any others currently in production worth buying?

New big block aluminum water pump housing - $70 + shipping (Paypal F&F, postal money order, or check will work). Located in West Sacramento, CA. PM me for a shipping quote. I'm guessing it'll be around $20 or so.

For those of you with a '64-'66 Dart GT, can you do me a huge favor and look at your front window sweeps (cat whiskers). Are the front inner and out cat whiskers supposed to be the same length? I just installed a set on my '66 Dart and I feel like the outer one should be about an inch longer.

Cast iron big block water pump housing. #3698468 casting with passenger's side radiator hose. It's pretty crusty and will need a good clean up. $45 shipped from West Sacramento, CA (PP F&F, postal money order, or check). Or $20 local pick up.

I picked this up for a A518 swap, but turns out my non-lockup A518 takes a regular 727 yoke. This was used with a 46RE. Not sure if it'll fit later lock-up 46RH's. Uses a 7290 u-joint. $40 shipped from West Sacramento, CA (PP F&F, postal money order, or check). Or $20 local pick up. If desired...

I picked up a slip yoke for my 46RH today at a local auto wrecker. It came from a '95 Ram 1500 (2WD 5.9) w/ what looked like a 46RH/RE. It had a 2-piece drive shaft for what it's worth. I figured that slip yoke would work on my non-lockup 46RH, but it doesn't quite want to slide on. It'll start...

Does anyone happen to know what size u-joint a stock 46RH/RE slip yoke uses? Are they 1310 or 1330's?

Are the lock cylinders for the decklids on these A-bodies supposed to be oriented with the pins on top or bottom?

Anyone have an extra window crank/door handle screw laying around. It's off a '66 Dart, but I'm sure they're pretty universal. They're about 3/4" long and have an allen head. I seem to be missing one. Thank you!

Anyone have any extra one of these clips for the trunk torsion springs laying around? Thanks!

I'm putting the back end of my '66 Dart back together and I think I must be losing my mind. I realize these round white foam gaskets are for the rear bumper, but where exactly do they go? Do they go between the brackets and the mounting points on the car? Other than the two out ones that...

I picked up a non-lockup 46RH a couple weeks ago and it came with the torque converter that was with it (originally from a '92 Ram w/ 5.9). Can I use this converter in a 727?

Do you any of you guys have a source for the rosette rivets for the a '66 Dart? Obviously, these are attached in the door jams, so I'm unsure if they are the same rivets as the later model A-bodies that seem to be the rivets that the resto shops like ECS carry.

I'm considering purchasing a car part from someone in Canada (I'm in California) and am trying to figure out how the fees/taxes work so I know how much I need to pay him. Will I be charged customs fees when the item is delivered? If so, how are those fees determined? Also, does Paypal...

For those of you who make your own battery cables, what ends do you use to terminate the cable on the battery end and connect it to the battery? I'm trying to find a clean, reliable battery lug end for some cables I'm making and looking for some ideas. Thanks guys.