Search results for query: *

Seen lots of U.F.O.'s Ugly Ford Owners

Obviously it is not a factory car or it would be worth a lot more than $55-75,000 But a nice looking car anyway! Now let's see if I sell my car and truck, and get a mortgage on my house, and sell the wife's car I could afford the car but not the tow home with it ... better pass !

yep I ordered the wrong speedo cable (my fault not theirs) and they sent me another one AND refunded my money. When I returned the original cable I added a note about the refund and they said "enjoy" can't beat that kind of customer care

looks to me like they have "special parking " place for vettes or car wash

or get a spark plug thread chaser and go easy with it till you know its straight then go in 1/2 turn then back out then in an additional 1/2 turn until you are down to the seat. If you screwed it up bad you can always put a heli coil in it

If I remember right 1 and 6- 2 and 5 - 3 and 4 run together. On inline 4 and 6 and straight 8s are this way and I used the system of when rockers on 6 are both rocking(exhaust closing -intake just opening) set both valves on #1 follow the firing order for next cylinder and so on. As for adding...

there is nothing flimsy about them except the price. and I can use the $800 difference for other things

thanks for all the help! I thought it was just me who was blind when welding. I can weld well if I can see where I'm going

check out Scarebird. I converted mine to disc for under $300 with all new parts (or reman) and I have been happy as a pig in sh*t for the last 4-5 years.

I've had it!!! I have a U,S. Welding auto dark helmet and I can't see a damn thing thru it, To begin with it has a dark green lens in it that you need extra lighting to just see where you are gonna weld, Then strike an arc and it goes so black you can hardly see the arc of the welder. and yes...

Always run a relay on anything high voltage/ amperage. it takes the load off your switches and controls - other wise running 90-125 amps thru the ignition switch will heat it up and cause intermittent connections on anything that gets power from the ign switch

I got mine at advance auto parts in the" help" section

nothing cleans gunk off of an old car like dawn and hot water and a medium stiff brush

That is way high Do you have a 4x4 places around you they make hydralic hoses for plows and can do a/c hoses too. Also take measurements and go to the junk yard most hoses use the same ends just look for length

To get 4" of lift without shackles or air shox or new leaf springs is going to be damn near impossible. Shox don't raise a car they control bounce (might get a little lift with new gas shox but not much). Short of adding a helper leaf spring and coil over loads on your shox or both you can't...

I'll know more about the accurracy of the mold today as I re make my tilt mechanism and start to align my seams.

don't know buit I think someone in the twin cities cast it and I was told it was from re worked molds MAS used . Much better than anything MAS put out and a damn site cheaper too!

I started to about a month ago and gave up. Buying pre bent mandrel bends was too expensive .

Saturday morning I went up to Minnesota and picked up my new one piece front end. And was impressed with the quality of the piece. The fiberglass was pretty nice with the uniformity of the glass- very even thickness everywhere. Also all the corners and curves were very nice and smooth. There...

10 worst paint jobs in the world the best of the worst

No every time I had a block boiled out there was very little of the paint left and as far as the cam bearings go, I have seen them slightly off which is ok but to barely line up is not take it back

There are 2 properties when checking a fuel pump. 1 is pressure and it sounds like you are ok there. the next is volume a pump can have proper pressure and insuffient volume. I don't know what the volume is for your car but I would venture a guess that if it pumps a cup of fuel in 15 to 20...

i agree with GTS... why go to the expense of rebuilding and adding alum heads ttochoke it off with stock exhaust

they always come in felpro intake set

The biggest problem I see with a 2 x 4 carb setup is most people take a near stock motor and then throw a pair of 750 's on it and lug it around town and wonder why it washed the rings out or they have so much gas in their oil and spin a bearing and blame it on the 2 x 4 setup My self I am...

I have in the past shortened both inner and outer cable.I cut off one end of the outer cable and duig out the old piece then taken an old pair of wire crimpers and ground them to make a cable crimper out of. For thye inner cable it is not as easy. After you determin the proper length, before you...

interested? Hell yes I am :color:I sent a pm but forgot to include my email so 2nd pm on its way

NAPA makes all kind of hoses around here ... maybe by you too

I am looking for either a one piece front end for a 68 cuda or a pair of fenders ships to 50317 (Iowa)

Looking to buy either a One piece front end or a pair of front fenders for a '68 barracuda (hood not needed ) ship to 50317 (IOWA)