Search results for query: *

$5000 obo 318 v8, 904 tq, 7 1/4 rear. Runs, drives, currently licensed/insured. Needs rust work, can pm pics of problem areas. Also have brand new year one metal for separate price. Top is in good condition, retract / extends perfect. Located St Louis county (Affton) Missouri.

Took the 472 Hemi 1969 barracuda to test n tune at Gateway in Illinois Wednesday. 1st time ever for me or the car. Apparently a Holley 830 cfm double Pumper on a mopar dual plane isn't enough for this motor. I was topped out by the 1/8 mile, went 14.5 sec, 94 MPH. I think it needs...

My car is a project that has no defined end state, so it's turning into some Frankenstein in-between sort of ride. Case in point : I wanted 3" exhaust out the back in order to license it for the street. There isn't enough room for that and the stock gas tank. so the trunk mount battery will...

My painless harness went in great, but they refer you back to the original harness for more than a few things. I don't know where I put the engine harness I took out. Does anyone know how to hook up a 1969 two speed wiper motor? The original switch has two output wires, the motor has a...

This is a duplicate I posted in Members Restoration, forgetting that there's a wiring section. Waiting for painless to give me some suggestions, this is what I posted to them, hoping someone here has some ideas too. Hi all, It needs to be said that I've been working on installing this...

The following is what I posted at Painless Wiring's help forum. While I'm waiting for them to get back w/ me, I'm wondering if there's anyone here with some ideas. Hi all, It needs to be said that I've been working on installing this harness p/n-10127 on and off (mostly off) since July...

Just used the plastic to buy the Eastwood welding setup. It looked like I was going to pay. Out the wazoo for a body shop to fix the ragtop. I might as well come out the other side with some new toys, and I never got it when somebody paid to do a car and then took it to a show

Cost $2k, and I got $2k of year one metal. Just need time. Runs and was licensed when I bought it last November

I would like to know if I'm the one that's wrong here. I will loan tools out to anyone who takes care of them, and brings them back w/o me asking when the job is done. If I find out that my tools are borrowed and then used by that person to make money, then I don't loan to that person...

Bought one, and it's installed forward of the firewall. Aft of the firewall, not so much. Any advice? The wiring diagrams that came w/ the harness are not the greatest.

I need help. (mental) If somebody gives me a HUUUUUGE price for something I want to buy, I initially balk. If I have an idea about what it costs, and I can roll it around in my head for a while, then the price seems more reasonable when I hear it. Here's my latest purchase: a 1969 318...

just brought home a 1969 barracuda v8 ragtop. Starting to realize the mandatory overtime at work is going to cut into the rust repair this thing needs. (rear quarters, trunk floor, floor pan, rockers. ) Need a reputable shop in stl

for a 4:10 rear gear - anybody an expert on this?

I want recommendations for manuals. The factory ones, while desirable, are going to break the bank. Anyone got some ideas?

So, Monster Mopar happens, and I BARELY get Jezabel out to the show, because she died on the way there. Then it becomes a mission to get her there, so I borrow a trailer and drag her with the Dak, all the while conscious of what a bad idea it was to tow it with a small truck (electric brake...

OK. Put the new tranny and stall in the Hemi Barracuda, and drove it around. Going about 15 mph, pulled the shifter back into 1st, and got on it,(not very hard), got into second, never got over 4000 rpm, and then it starts misfiring like it's got a bad vac leak. Now refuses to idle, and...

Brand-new trans, converter as full as I could fill it before install. How many quarts to put in before I fire the motor?

Never really got it. I do now, check out the bolt head indents. BTW, it didn't hit me until I ordered a converter with a billet anti-balloon front plate. The bolt head indents are from the 400 "B" that the converter spent some time on. (6 bolts) The gouges on the outer radius are from...

I guess there's a resistor for the slower speeds- anybody know where it's physically located in a 2003 dak?

I'm getting closer to getting her street legal... It'll be almost 4 years since she had plates.

I must be insane. I left the airlines 3 years ago, because the situation at American had become intolerable. That ended a 12 year run in aircraft maintenance. I've been through at least 10 jobs in that time, each time to go on to a job with better schedule, pay, growth opportunities, or...

****Go To The Political Forum With This Stuff *****

I like steel rims on my car, but i'm tired of the chrysel ralleys. I'm thinking nascar steelies. where can I get them?

Well after 3 months of leaving it in "D" and mashing the throttle, lighting up the hides, the 727 started to slip. Dropped the pan, and all kinds of metal/gook/stuff in the pan and filter. Guess this one's done for. I got 3 more units I can build while leaving this one in the car. I'd like to do...

At my new cube in TUL, I've put up the ugly pics of my Barracuda as computer wallpaper, and of course all visitors now inquire about the car, the ones it's a copy of, and what they're all worth. I know mines barely worth the price of the engine, but what are the real Hurst cuda's and darts...

I have to admit, I'm not a master tuner, I'm lucky this obscenly expensive motor is holding together. I'm starting to wonder what I will find out when I finally get some sticky tires on it if the money situation ever loosens up. For example: I wanted this thing to survive on crap gas, so it's...

I don't exactly like the idea of paying huge amounts of money for a paint job I know I'll chip/scratch/otherwise mess up. So how's this for an idea? The original B029 barracudas were delivered with a grey primer body w/ a black gelcoat front clip. I know mine's a '69, but I'm thinking this is...

Just checkin to see if my new avatar works... I'm sure she does, somewhere.

I am so incredibly mad. There's a thread back on Moparts.com that has to do with the impending ban by the EPA on anything to do with private citizens getting hold of body/paint products with VOC's. Of course I expect the EPA and the treehuggers to be our enemies, but there's a member on there...

:downtown: At some point, I want to make a pass down the track. Where can I get info on what I have to do before this thing gets on the 1320? You know, how the trunk battery has to be tied down, how much rubber tubing total allowed in fuel sys, etc. PS just had to use the downtown smile, that...