Search results for query: *

'63 GT hardtop. Built BH block 225 with Offy/Dutra manifolds, A833, 8 1/4" SureGrip 3.21, disc brakes, V8 torsion bars/rebuilt front end. New bumpers, clean black interior with nice leather bucket seats. New windshield and seals. Nice solid restomod driver. Clean title, current reg with black...

Mostly completed the mechanical stuff on my '63 Dart: rebuilt '74 block 225, block decked 0.40, polished ports/hardened valve seats, Offenhauser intake with Holley 390, Dutra front manifold/cut rear manifold, 10" clutch, A833 trans, 8 1/4 Sure-trac 3.21 axle and all rebuilt front end with '74...

I need a cast iron bell housing to mate a 1972 A-833 to a slant six in my '63 Dodge Dart. I believe the part numbers are: 2463025 2463027 2468431 Also need a clutch fork and early A-body Z-bar Thanks Marc in SF

I have the interior of my 1963 Dart GT hardtop stripped for restoration. Both front and rear windshields have been redone with Steele Rubber gaskets and, after much struggle and returns to the glass shop, are now watertight. While testing with a shower nozzle on the hose, I noticed that the...

HI I have an A-833 A-body trans with Hurst competition shifter/rods, date code Jan 1972 and I am willing to trade for solid A-833 OD A-body trans. I'm in San Francisco CA and would prefer a fairly local trade, given shipping weights. Willing to travel in CA to meet. Thanks Marc

This is a bit off-beat, but my '63 Dart GT 225 /6 has a trashed and incorrect radiator and I'm trying to decide which way my (cheap) budget can take me. I'm not a restoration purist, and the original "big tank" unit is long gone so recoring is not an option. I have done a bit of performance...

I have a '66 Dart 225/904 automatic and need a gas pedal with floor mounting bracket/link to bell crank and kick down linkage complete from throttle rod to transmission lever. I believe any from '64 to '66 Dart or Valiant will work. Thanks! Marc in SF

Replacing the original 225 in my '63 Dart GT with a rebuilt 1974 225 and need a large hub flywheel to use with an A833 I'll have the original flywheel available to swap if needed. In SF California Thanks!

the accompanying pics are of an automatic trans currently installed in a 1966 Dodge Dart GT with a later slant six engine (five freeze plugs, 280xxxx casting number, tapered rib behind the water pump housing, spark plug tube head). It's difficult to get a clear shot of the driver's side pan...

A bit complex, but here goes: I have a nice '63 Dart GT with an A833 (Jan 1972 production date on data pad) installed in the dim past by a previous owner....no details available. I believe the car has the original somewhat tired 225 /6. I have an opportunity to buy a '66 Valiant with a nicely...

Installing carpet in my '63 Dart GT; the interior was pretty gutted when I bought the car, so I have no frame of reference for how the carpet fits at the accelerator pedal. Search of this forum yielded a helpful post about carpet interfering with WOT, but not the issue I'll describe below...

Here's the situation: 1963 Dart GT 225 /6 with a 1972 A-833 close-ratio box installed in the distant past (no history) Rear axle replaced with a big bolt pattern 7 1/4 from an auto '75 Dart; 2.76 gears Result: feels like launching in second gear! Have to slip the clutch, barely get...

No luck so far on locating a source to replace the 10 plastic push-in trim clips for the roof/quarter panel trim on my'63 Dart GT. Haven't pulled the side moldings off yet, but I suspect there will many more underneath. I was able to remove the clips by drilling a hole in the center push-in...

I'm prepping my semi-beater for a two-stage rattle can paint job (local paint shop matched the paint in base coat and loaded it in rattle cans) and would like to remove as much of the trim as is practical. I understand a lot of the '63 GT trim is year/model specific and REALLY don't want to mess...

Removed from a 1964 Dart parts car and for sale is a complete Kelsey-Hayes small bolt pattern front disc brake set up. No history on the car or parts, but judging by the accumulated dirt/crud on the car, the setup had been in use for a long, long time. Included are spindles, bearings, upper...

Just bought this '63 Dart GT and am pretty skeptical about the originality of the two bolt-on hood scoops. The car had original (extremely greasy and stained) fiberglass insulation intact in place which I removed to assess the damage: the fasteners look pretty original so I'm puzzled...

So I found a very nice gentleman on local CL with a '65 Barracuda factory four-speed car with a stripped out interior who allowed me to splash a mold of the tunnel hump. I had to drive to San Jose and work in a warehouse for a limited amount of time, so I used 6" orthopedic plaster and mold...

Looking for an A-body 7 1/4" axle with 5x4.5" bolt pattern and deep gears; I've read that they were available all the way to 3.90 I currently have a '63 Dart with a 7 1/4" axle from a '74 disc brake automatic A-body and the 2.76 ratio just doesn't cut it around town in hilly/traffic-clogged...

Hi! I'm new to both Mopar and this forum, andI realize this topic has been discussed several times before but I still don't see any resolution. I recently acquired a 1963 Dart GT, originally a 225 with a column shift three-speed, that was converted to a A833 four-speed. The basic work was...

Just finishing up with a front end rebuild with a disc brake conversion on my first Mopar (1963 Dart GT) using 1974 Dart spindles and UCA; using heavier torsion bars, 195/60-14 tires on 14x5.5 Rally wheels and would appreciate any suggestions on what brand/type shock absorbers to use. The car...

I'm doing the '74 A-body disc brake conversion on my '63 Dart GT, and replacing all the front end bushings while it's apart. The right side lower control arm bumper ("jounce" bumper, per the manual) is completely gone on my car....just the mounting bolt and nut remaining. The left side bumper...

Other than the $105 PST polyurethane unit, can anyone provide me with a source for a transmission mount for a 1964 Valiant with a 225 /6? many thanks! Marc

Hi! New to both Mopar and this forum....great site! I just bought a '63 Dart GT, and it needs both front and rear windshield gasket's/seals. I understand that the rear gasket is a 1963 only item, and pleased that there are at least two sources for it (steep price, but at least available!)...

Hi New to both Mopar and this forum....great site! I just bought a 1963 Dart manual shift car that had a Hurst floor shift and 833 installed in the distant past (no history from seller) I noticed the clutch pedal not returning to the top, so adjusted the rod at the release fork; pedal...