Search results for query: *

Can't find the mopar purple cam 280/474 anywhere, I had that cam once and loved it nice idle and pulled like a fright train.what I like I was able to use stock push rods and rockers,just had to change valve springs comp 904.if I can't find my old cam what is a dead ringer close specs as the 280...

I have a set of 71 318 B body engine mounts will they work on a 70 A body Duster.that has a 318 thanks gents.

Well I got time to change the mounts ,driver side almost tore in half passenger side not to good either, they wear 2 years old.went with Mancini will see how they do against the torque monster. I am glad I had the left side chained up.

Just notice this today,I don't remember the 360 with a lean,I do have the left mount chained down,have a look see.

Do you fog you engine for winter storage,I have never done this.thoughts please.

Looking for your thoughts,on another cam.my old 360 Dart had the purple cam 474 280 nice sound and performance.my build now is 360 speed pro pistons 30 over 9 2 1 340 J heads 202 valve Edelbrock RPM PERFORMER intake hooker headers 268 comp cam, my engine builder says that's a small...

Well i got my rebuilt 360 broke in the outher day, but when are the rings broke in, the 360 has had 2 fire ups ran 20 minutes booth times,no isues, sweet.my engine builder says to get some 10 w30 royal purple synthetic, is it too soon to run synthetic, i know we want tones of Zinc, myself i like...

Good day gentsssssss.my la 360 is at the machine shop, i am looking for some help on picking pistons. Keep in mind my budget is low.They are doing a stock bottom end rebuild, i am shooting for 20 over 9 to 1 piston,not sure about the KB heard lots of bad reviews,so can someone shed some light...

Had the 71 out yesterday,getting her ready for this summer.As i was backing into my drive way there a noise, a scraping sound.So removed booth belts,thinking water pump,or power steering,nope still there,check convertor bolts tight,my gut feeling is its internal.What a drag,with almost no...

This 71 Satellite 318 is ready for the engine install.So with headers that old hevay starter has to go,so could you gentsssssssssssss start me on the right track,as to what year, make,on the smaller starter to get,with out any mods to get it in. thanks again.

71 Satelitte 318 has A/C. It has power steering also witch I plan on keeping..I want to go without the A/C, SO what do i need to change over.This is new to me so any help will go a long way.

Lost my notes, sorry.The 360 is going to sit for the winter,no start up for another 6 mounts.The comp lube they gave me runs off,so whats is the best lube that sticks on camshafts and lifters.Next build,roller cam...................

86 360.In the first pic you can see the upper right coolant passage.When i put the gasket on the second pic that passage is block,if i flip the gasket the passage is open,but the dowes dont line up.Same thing with the outher gasket,and same thing on the left bank.What up this is the gasket i...

Looking for some ideas,what to use to plug the smog holes on my 360 head.Could a self taping screw work than grind of the head to get a flat finish.Or whats your thought JB weld fill that hole and be done with it.Looking for a cheep long lasting fix.I have the 340 exhaust manifolds,that don't...

If I remember,95 is the number for torquing my stock 360 heads.

I have everything now to swap out the springs,the heads are off.So whats a good spring compressor,I want to do this myself. So whats out there,and any tips on removing the springs and installing the springs and the seals.

I need you all help again,i know 901-16 valve springs what is the part numbers for the retainers,and locks,the engine builder say I would be wise to get new.Or is my stock stuff still good.Tankssssssssssssssss.I may buy the valve spring compressor and do this myself.

The 4343475a 360 head,how much in flow #ssssss VS the x-j.Are my heads any good to use,the bummer is there smog heads.

In the pic there are two gaskets, the brass looking is left over for another build.The gaskets i just got have 1 that looks different than the outer,it looks like metal in the middle and gasket material on booth sides.I assume that it goes on that big bolt,there is a cork gasket that goes inside...

Looking for your thoughts on Head gaskets.I have all ways used the Fel-pro blue,never payed attrition to thickness,its a stock bore 360,is there a thickness that would give me a better compression with out any lineament problems.Intake,heads have never been milled.Also don't want to play with...

Well the cam is in,trying to find someone around here that knows how to degree a cam and to come to my place is like pulling a crack ***** teeth out.There is only 1 guy who will do it,but want me to bring the engine in,a well know machine shop,they have a great engine builder for sure,but i had...

Next IS THE OIL PUMP,Should I get an HV pump or stock,does the HV cause oil leaks,thinking too much pressure.

OK I did get a cam yesterday,so now I am on to the heads,i know i will need new springs comp 901,but whats up with the exhaust vale springs.Why is it different.I know the comp springs will work,but do in need new retainers on the exhaust side? also these are smog heads, some 340-360 are some...

Have dun some searching here and found that when buying a camshart you do not have to buy the lifter the cam maker sells,like comp,they have had a few bad ones true or false.

Check out the cylinder wall,is this going to be a problim.It looks like rust marks. 80 THOU MILE MOTOR.

Just pick up a set of Moroso valve covers with matching 14 inch breather.There is no baffles for the pcv valve,there is no were under to screw in a baffles.So does any 1 know of a grommet i could use that works with my stock pcv valve.I have a grommet left over from moroso that has a slit in the...

Stock 360 2500 stall with 323 gear.RPM performer Edelbrock 650 Holley re-curved dizzy,stock 340 exhaust manifolds.What to you guys think about the XE256,or the XE262, comp cams.Let me have it.thanks the first 1 is close to stock and the second one is a little milder.

How can I remove power coating,chemical or sand blasting.

Will installing the 901 springs with the stock cam hurt anything? I have not made up my mind as yet to what cam i want,if any.

Well it was a road trip for sure,took 2 hours to get this intake.Nice guy,he has a 74 Challenger,and his buddy died and left him some parts,and a 74 Cuda.He has some cams as well this 1 is new Hughs HEH 1523al,can some 1 shed some info he is asking 60.