Search results for query: *

Looking to possibly sell my entire engine, transmission, Ignition, and fuel injection combination (Less than 1000 miles on entire set up) to start a different engine project. This is a pretty fun and fast engine combination for the street. Engine: It is a 2001 5.9 Magnum stroked out with a 4"...

I have this small block electronic ignition conversion kit that I bought in May 2021. It is the Jegs brand, and works flawlessly. I am swapping in a new engine and going to the Holley Hyperspark ignition. It is a billet aluminum distributor (does not say "Jegs" on it like the pic), blue...

I have a 42 5/8" long driveshaft, made by Precision Shaft Technologies. This was in my 1968 Barracuda with an 8.8 rear end and 46RH/A518 transmission, and will fit any 108" wheelbase car set up the same way. My 8.8 is shortened 3" and the flange is centered in the differential. I had it was...

I have a brand new set of 16 Edelbrock "Roller Cam" valve springs from a set of 61775 Heads. These are dual springs with dampers, 7 degree locks and keepers, on an 11/32" valve stem. Edelbrock tells me that Summit Racings spring rate listed (465 lbs/inch) is wrong and that they are 420 lbs per...

I have a brand new, in the box and wrapped in the original plastic Edelbrock RPM Air Gap intake manifold for a small block LA. I bought this and ended up changing to a 5.9 Magnum. I will sell for $350 shipped from Laurens, NY.

I have the jack and holder spring from my 1970 Dodge Dart. It does not look like the jack was ever used or even removed. I live in Laurens, NY 13796. I will sell this for $75 OBO shipped to your door in the lower 48 states. What you see is what you get, still haven't even removed it, I just...

I have a used 22" radiator. It was bought new and used for approximately 1000 miles. I also have 1 piece shroud that can go with it, or separate. I had this in my 1970 Dodge Dart with a 318 automatic. Has the transmission cooler built in. No leaks, issues, works great. Prices are shipped in...

I have a Hemi engine cover for a 5.7L. It came off from a Chrysler 300. It is in upstate NY, $110 shipped to lower 48 states. The silver, center part is removable if looking for custom painting. Open to trades...

Selling a Walbro inline frame mounted fuel pump. It flows 60psi and includes the insulator sleeve and mounting brackets. $110 shipped to lower 48, add $6.00 for Canada. Located in Laurens, NY

I bought this MSD in line frame mounted fuel pump with in line filter/regulator and fuel line fittings, including fuel rail adapter. I paid $169.99 plus shipping from speedway motors, selling for $155: http://www.speedwaymotors.com/LS1-Complete-Fuel-Delivery-Kit,41792.html This is the...

I have a pair of 73 and up motor mounts that have been sandblasted and coated with POR-15. These look very nice and are rust free. They need the inserts (which you can get through summit, cheap) I am asking $30 shipped to your door in the lower 48 states. I am located in the Upstate NY area

I have a used set of Magnum Force tubular upper control arms. Both ball joints are in good shape, one of them needs a boot for the ball joint. It did not go bad, I tore it when I took it apart . These have the larger 1973-76 ball joints and the bushing are already installed. I am asking $150...

I have a rebuilt 340 for sale with a rebuilt 904 transmission. The engine has the following: 1973 block bored .030” over 10.5 to 1 TRW forged pistons w/moly rings, rods resized and bushed w/floating wrist pins and new locks Pistons and rods balanced ARP bolts crank polished Clevite...

I am selling two seperate torque converters for a 904 transmission. The first one is a Dynamic 11" Street converter, website shows a 2600-3200 RPM stall speed based on application. Part number is 11741 904MX. has about 250 miles on it. Features - All fins are heli-arc welded for...

I am selling a Holley 3310-3 carburetor. It is 750 cfm, square bore, vacuum secondaries, manual choke and has about 200 miles on it since rebuild. It runs great and needs nothing. It also has the dual inlet braided steel line with an -AN fitting. It comes with an one inch thick Edelbrock 4 hole...

I am selling a brand new set of RMS Spring relocation boxes that I bought a few months ago and have decided to go an alternate route instead. The boxes are drilled with four separate mounting positions (stock position, 1.25" lower, 1.5" rearward, and 1.25" lower with 1.5" rearward). I am also...

I have a new carb rebuild kit that I bought from Rockauto by accident. It is for a 2 barrel, CALIFORNIA EQUIPPED Carter carburetor. I did not realize it was for a Cali Carb until I opened it. This cost $19.25 plus shipping at Rockauto.com. RockAuto describes as: STANDARD MOTOR PRODUCTS Part #...

I am selling a brand new, never installed set of Just Suspension 1" diameter torsion bars. These are great for pro-touring and street handling. I bought these to put in my 72 Dart and decided to go a different route with the suspension. I also am including a set of polyurethane dust boots from...

Not mine, but I figured I would post it: http://utica.craigslist.org/pts/2524747837.html states as follows: for sale 1971 340 engine casting #2780930 date 6-14-71 I have the block,camshaft,steel crank,timing gears,cover,balancer.block looks to be standerd bore.$450.00 obo the email is...

I have a set of Hotchkis front leaf spring hangers for sale. I bought the Leaf springs from hotchkis, and do not need the hangers from the kit as I am relocating my springs to the frame. These are brand new, never mounted or test fitted, they are powder coated black and come with grade 8...

I have a set of 30 Spline, Dana 60 axles with green bearings and 3" screw in studs installed. The axles are for 54.625" wide Dana 60 with a stock pinion offset (drivers side 1.375" longer), from wheel mounting surface to wheel mounting surface. THESE AXLES WILL NOT FIT ANY STOCK WIDTH HOUSINGS...

I have a set of Dana 60 axles with green bearings and 3" screw in studs installed. I also have a set of moser axle ends to go with it. The axles are for 54.625" wide Dana 60 with a stock pinion offset, from wheel mounting surface to wheel mounting surface. As per Doctordiff, these axles have...

I found this on my local craigslist if any one is interested. It is not mine, do not know the persons who has it: http://binghamton.craigslist.org/pts/1932826133.html

I am selling a Holley 4 bbl carb cheap... read on, you will see why it's cheap. The numbers on the side are 6R 4585 B. Which is a 600 cfm carb. This was on a friends derby car that caught fire and put out within 30 seconds. This is mainly for parts. It still worked when pulled a couple years...

I have a 500 Cu in big block from a 400 BB, it was bored 0.33 over with Keith Black forged pistons, 9.76:1 compression, 440source aluminum heads, Hughes roller cam, Eagle H-Beam rods, Hot tanked, painted Chrysler Orange, coated cam bearings, Cloyes Hex-a-just double roller timing, 440source...

I have an 8 3/4 rear with a 742 housing. The rear is 61 1/2" wide and is non-suregrip and is around a 2.90ish:1 gear ratio. The rear is the correct width for E-Bodies and C-Bodies and can easily be cut for A-Body width. The rear has been stored indoors and needs to go because I am moving 4th of...

500 Cu in Big Block (400 block), Freshly machined, internally balanced, and painted Hemi Orange, never assembled. Engine is ready to be assembled. Bored .033" over. 4.15" 440Source stroker crank KB forged pistons with full floating pins Eagle H-Beam RB rods, with ARP Bolts 440source...

This is not mine, but I found on my local craigslist. I will not be able to go get it or look at it being it is about 2 hours away, I just figured someone here would be interested: http://binghamton.craigslist.org/pts/1790596924.html

I accidentally bought a set of ARP Cam bolt kit for a Big block 3 bolt cam. They are the ARP's part number 144-1001. They are Chrome Moly, Black Oxide. Thread size is 3/8-16 in. They are brandnew, unopened. I bought a cloyes Hex-a-just and summit said they do not come with the bolts... they do...