no, I think what I posted is the magnum gasket. I have the LA too....
2019 summer race.... Jadaharabi vs 318willrun
- Thread starter 318willrun
- Start date
-
j par
Well-hung Member
I always use the 1213s...
those head gaskets are only like 17.99 each over the counter parts store...
j par
Well-hung Member
They're 14.95 on Summit...
j par
Well-hung Member
It's like a second job busting your chops on this forum LOL...
If you order 100 dollars of stuff. Which this is exactly where these came from. I need a few more dollars for free shipping so I threw in a set of these... LOL
Well, get on board with me! This would be an 11.90 engine in a mild street car for 2500 bucks bought, built, and throttled! Carb to pan!
j par
Well-hung Member
I think I might have to file a workman's comp claim... Triple R hurt my feelings the other day when he told me I had no friends.. I hadn't heard a comment like that since grade school!..lol... ten bucks says he's been waiting since grade school to finally be able to say that to somebody else instead of getting said to him..lol...
j par
Well-hung Member
Been there done that...
I like them too. but lately have been using procomps version for budget reasons.
Mopar Chrysler SB 318 340 360 Intake Manifold Gasket Set 1213 2.27" x116" x0060" | eBay
Where did this post ^^^ come from in the middle of this conversation?
LOL...
j par
Well-hung Member
GOTCHA!!!...lol...
Does that include the free Holley carburetor? Are you still running a cast iron intake manifold?...
We better start adding stuff up you know where I'm going next...
any sealing problems?
j par
Well-hung Member
You didn't read the post about busting your chops being a full-time job. I'm on the job...Where did this post ^^^ come from in the middle of this conversation?
j par
Well-hung Member
Nicelink! I'm all over that!... Pro Comp rules!!...
j par
Well-hung Member
Hello McFly? Avoidance isn't one of your strong points...
No. Son's had 3 sets on the valiant. Only replaced them each time he changed cams.
this would be carb to pan engine.
- long block 400 dollars
- 750 DP - I believe 150 (been a while)
- intake - I have a stealth -150
- ProMaxx - 1437
- Cam/lifters - 220
- intake/head/timing cover gaskets/fluids - 100
I may try these next. Is that the actual gasket or just an image in the picture? Asking because it looks like the heat crossover is blocked?
j par
Well-hung Member
Plus headers cough cough....this would be carb to pan engine.
Grand Total of 2457.00
- long block 400 dollars
- 750 DP - I believe 150 (been a while)
- intake - I have a stealth -150
- ProMaxx - 1437
- Cam/lifters - 220
- intake/head/timing cover gaskets/fluids - 100
Also, I would have a extra cam/lifters and heads, all good, 13.3 proven with 2.94's LOL. If I sold them, the cost would lower.....this would be carb to pan engine.
Grand Total of 2457.00
- long block 400 dollars
- 750 DP - I believe 150 (been a while)
- intake - I have a stealth -150
- ProMaxx - 1437
- Cam/lifters - 220
- intake/head/timing cover gaskets/fluids - 100
exhaust isn't part of the cost. neither is converter, or gears. I don't count the cost of your 4 speed, clutch tamer, Dana, or tires as part of the cost of your engine either.
j par
Well-hung Member
Alright stop bullshiting! Selling old parts to make up for the new ones please...Also, I would have a extra cam/lifters and heads, all good, 13.3 proven with 2.94's LOL. If I sold them, the cost would lower.....
j par
Well-hung Member
I never knew that was part of the calculations!?.... You never knocked any of that off my supposed 6K motor...
They are hard to tell from felpros, except sometimes they come with red printoseal instead of blue, never know until they get here.I usually buy 3 sets at a time to save shipping. We are using them on my son's magnum, just had to cut slots for magnum vertical bolts.
-
