I found a couple well used (dented) dust covers. I’d like to find some new ones but at $13 or more for new ones each, might have to let the Magnum 500s hide the covers
65 Dart Wagon Conversion to a Sedan Delivery
- Thread starter 65 Dartman
- Start date
-
I’m getting ready to install the rotors and front brakes - NOS Calipers and hold down hardware I bought from @slantsixdan, new F Body brake hoses (the calipers will be mounted to the rear so the longer F Body hoses are required), and new Wagner semi metallic brake shoes through Amazon
I found some used hardware to secure the rotors to the spindle (one set shown)
But decided to order new since I only had one special washer
I’m in a quandary about the well used and dented dust covers. Do I use the used and hide them with the wheel or bite the bullet for new ones?
I found some used hardware to secure the rotors to the spindle (one set shown)
But decided to order new since I only had one special washer
I’m in a quandary about the well used and dented dust covers. Do I use the used and hide them with the wheel or bite the bullet for new ones?
I would go black. Such a great restoration demands black front end components.
You’re correct! The adjustable strut rods were finished in gold. I painted them black as well as the tie rod sleeves
Installed each rotor and then caliper with new pads and bleeder at the top. I’m surprised that the caliper holddown packet had 12 mm bolts where the bolt holes on the caliper adapters was 5/16th NC. I will get to Lowes in a day or two for some Stainless Steel bolts and washers of the correct length
I need to raise this side (passenger side) so it won’t slide on the floor.
I need to raise this side (passenger side) so it won’t slide on the floor.
Nice work Don
old65-4spd
Well-Known Member
On my ’65, I mounted the rotors to the rear and had a problem with them hitting and preventing full steering travel. Luckily, I didn’t tighten everything so was easily changed back.
mygasser
Well-Known Member
calipers to the rear? not rotors? lol.
Thanks for replying. I am curious as what/where were the calipers hitting
To prevent the wheels from full steering travel.
old65-4spd
Well-Known Member
I searched all my pics and unfortunately wasn’t able to find any. Apparently when I test fitted and found the interference, I swapped back to the correct locations. All done without taking time to document with pics or notes. Sorry I wasn't more helpful.
But I recommend you test fit for yourself and make your own determination. Possibly yours could have something different than mine.
Before I did my conversion there were posts on various sites describing how easy it was to move the calipers to the rear. I didn’t get around to it for quite a few years, so did more research when I was ready for the conversion. There was nothing found about any interference with the relocation.
But I recommend you test fit for yourself and make your own determination. Possibly yours could have something different than mine.
Before I did my conversion there were posts on various sites describing how easy it was to move the calipers to the rear. I didn’t get around to it for quite a few years, so did more research when I was ready for the conversion. There was nothing found about any interference with the relocation.
I was just thinking - were you using - the 65-72 4 piston Kelsey Hayes or the 74-76 single piston like I’m using?
old65-4spd
Well-Known Member
I have the single piston like yours and swapped the spindles side-side. I don’t remember how much travel was limited, so if there was only a small amount then there might be a geometry difference between mine and yours.
My gauge cluster is a custom set of Dakota Digital gauges housed within a 66 Barracuda instrument bezel.
With the Dakota Digital system, up to an additional 16 specialty gauges can be displayed in the main menu cluster without having to resort to underdash or A pillar pods. I decided to add separate engine and transmission temperature readouts. It’s as simple as adding a 1/8 NPT bung to the oil and/or transmission pans (which I welded in place), add the sensor snd run the cable to the the temperature modules. I’ll add the cables just prior to lifting the engine, transmission and K Frame in place.
With the Dakota Digital system, up to an additional 16 specialty gauges can be displayed in the main menu cluster without having to resort to underdash or A pillar pods. I decided to add separate engine and transmission temperature readouts. It’s as simple as adding a 1/8 NPT bung to the oil and/or transmission pans (which I welded in place), add the sensor snd run the cable to the the temperature modules. I’ll add the cables just prior to lifting the engine, transmission and K Frame in place.
Last edited:
DCAspen
Well-Known Member
Dash cluster looks excellent, can’t wait to see it lit up
Knowing that my outer wheel bearings on my brand new front end brakes would be protected by one of these crappy looking, dented caps,
i couldn’t stand it anymore and bit the bullet and bought new ones.
i couldn’t stand it anymore and bit the bullet and bought new ones.
Last edited:
THIS IS NOT A FOR SALE AD!!
I have not done much of anything with the Dart lately as I have been trying to finish a set of 66/67 Charger front and rear bucket seats to bring to the Mopar Nationals. The back story on these is I had bought a 67 Charger from an acquaintance and later sold it back to him when he developed a severe case of buyer’s remorse. In between buying and selling back the car I found a complete interior - front buckets, rear buckets and buddy seat - in a junked and wrecked 66 or 67 Charger. So I grabbed the interior and then ordered a complete interior package from Legendary. Then eventually sold the car back to the guy who sold me the car. But kept the interior seats and upholstery stuff I had bought. Fast forward to several months ago when I decided to rebuild the seats with the new upholstery I had and take everything to the Nationals in August to try and sell. Even with new foam, burlap to protect the foam and upholstery, it’s not as easy as a simple install. I am within striking distance - both front buckets and the buddy seat are done as is both rear seat cushions and one rear seatbck. I am currently trying to get the other rear swatback ready for all the undlayment - burlap, foam etc
Prior to me pulling the seats at the junkyard, someone grabbed the driver’s side tracks but left the passenger side so I’m missing that track. One rear seatback is missing a couple of trim pieces
. If they don’t sell at the Nationals, i’ll have brand new seats fir my 47 Dodge
I have not done much of anything with the Dart lately as I have been trying to finish a set of 66/67 Charger front and rear bucket seats to bring to the Mopar Nationals. The back story on these is I had bought a 67 Charger from an acquaintance and later sold it back to him when he developed a severe case of buyer’s remorse. In between buying and selling back the car I found a complete interior - front buckets, rear buckets and buddy seat - in a junked and wrecked 66 or 67 Charger. So I grabbed the interior and then ordered a complete interior package from Legendary. Then eventually sold the car back to the guy who sold me the car. But kept the interior seats and upholstery stuff I had bought. Fast forward to several months ago when I decided to rebuild the seats with the new upholstery I had and take everything to the Nationals in August to try and sell. Even with new foam, burlap to protect the foam and upholstery, it’s not as easy as a simple install. I am within striking distance - both front buckets and the buddy seat are done as is both rear seat cushions and one rear seatbck. I am currently trying to get the other rear swatback ready for all the undlayment - burlap, foam etc
Prior to me pulling the seats at the junkyard, someone grabbed the driver’s side tracks but left the passenger side so I’m missing that track. One rear seatback is missing a couple of trim pieces
. If they don’t sell at the Nationals, i’ll have brand new seats fir my 47 Dodge
Last edited:
I haven’t done much of anything to the Dart as I was doing the 67 B Body seats pictured in my previous post. No, they didn’t sell at the nationals so brought them home of course. I’ll use them in my 47. So i got a very long list of stuff I need to accomplish in order to drive this thing to Carlisle or/both the Nationals.
My wife picked the one of the jobs for me - construct a new dome light harness. It’s actually a pair of LED lights to be mounted on each side above the shoulder belts. With new red and yellow wires taped up, it went together pretty easy.
My wife picked the one of the jobs for me - construct a new dome light harness. It’s actually a pair of LED lights to be mounted on each side above the shoulder belts. With new red and yellow wires taped up, it went together pretty easy.
-
