Search results for query: *

Looking for a set of metal slant 6 engine mounts for second gen a body. I was going V8. Sold the 170 with the mounts. Now acquired a hoped up 225 so going that route instead.

$2500. 1988 Dodge D150 LE. 318 TBI. Auto. Power windows, locks, steering, brakes, cruise, tilt, a/c. Air was rebuilt with all new parts last year. Needs a charge. Interior is in great shape. Tires have great tread just a little over a year old. Needs paint body and valve cover gaskets. Seymour...

75 Dart sport. 225 auto. New charging and ignition components. Car cranks and runs for 20 min. then cuts off like the switch is off. Power to coil, balist, ecu and dist. When it cools off it fires up and does it all over again. I replaced coil with a good spare and still no spark to the plugs. I...

So. I pulled the car into the parking spot. It had 30 psi when I cut the switch. 24 hrs later I go to start the car back up. 0 psi!! I just pulled the pressure relief valve. Clean it with croakus. Rinsed all out with Carb Cleaner. Fired it up and still 0 psi. 35k stock 225 in my 75 dart. I...

1975 Dodge Dart Sport. 225 Slant 6, 904 auto. No functioning factory AC. 36,000 miles on engine rebuild. 5k on rebuilt front end. Big block torsion bars from the factory. Handles great. Drum brakes but a Scarebird conversion plate kit comes with it for disc setup. Extra parts interior and...

I have a dead miss that occurs through the whole rpm range. Not as noticeable at wot but still there. I thought vacuum and changed intake gaskets and visually inspected valvetrain and intake. All looked good. Here is the engine specs. 360 .030 over bore. Flat top pistons with slight dish stock...

I posted this in the trany section also. But I know mostly post 66 guys lurk there. I have a 64 pushbutton 904 that thinks it is an sr-71. Napa use to have a full kit but not anymore. I need the park quadrant gasket and seal, and the gear selector seals. I can get the pan and filter set all...

I have a 64 pushbutton 904 that thinks it is an sr-71. Napa use to have a full kit but not anymore. I need the park quadrant gasket and seal, and the gear selector seals. I can get the pan and filter set all day long. Anyone know of a source?

I am need of a K frame for an early a 64-66. It is for my girlfriends car and the funds are limited. She bent it up an inch and a half and knocked it out of alignment. This is her daily driver and we need to get it back in service soon before I run out of time when my work starts picking up...

I have a friend opening a theater in Pigeon Forge. He is looking for a 39-47 dodge truck to use as an advertisement. Body condition; the more used the better. Prefer to be running at least. Bed is not needed, flatbed a plus. Prefer 1/2 ton but 1 ton will be considered.

Hey ya'll, I'll post this here and maybe get a broader audience. I am looking for the impossible probably. But my girlfriends 225 started knocking yesterday and she doesn't have the cash to rebuild. I'm looking for a running, low miles, or rebuilt 225 or will consider 198 in east tn. I am...

Hey ya'll, I am looking for the impossible probably. But my girlfriends 225 started knocking today and she doesn't have the cash to rebuild. I'm looking for a running, low miles, or rebuilt 225 or will consider 198 in east tn. I am located in seymour and she's in sevierville. I have one in NC...

Intake and exhaust manifolds. Located in Seymour, TN. 37865. I do not have linkage or carb. If I did it would be on my 75. Don't have the $ to buy them so I'm selling this. This thing is heavy, about 60 pnds. I am asking 100.00 plus shipping.

Instrument cluster No cracks, speedo works, Slight warp-age at top...$35.00...sold Center radio/htr trim, a little warped from someone trying to use a screw driver to pry off...20.00 Glove box door without lock...15.00 Horn ring w/horn mech pitted...15.00 3 arm rest from 4dr. 2 have broken...

Out at Pull-A-Part in Knoxville, TN. I found a 67 Valiant signet 4dr. The front clip is decent, Has the pass. side grill in great shape. Rear bumper good needing chrome. The rear trim panel on trunk lid in great shape also. Exterior door handles. Heater controls. Manual steering auto column. I...

I need the stainless trim and clips that runs down the both sides, 1/4 spears, and stainless that runs down the hood, and the stainless around the back window. Also turn signal lenses. The trim on my girlfriends car was missing when bought and I don't have spares in my stash. Any help would be...

I am thinking of going the scarebird route on my 75. The question I have is, are the LCA balls strong enough and will the spindles take the stress of daily driving? It's a 75 Dart Sport with a /6 w/ drums but, I don't remember if the ball joints are bigger or, if it only applied to the disc...

I've got a 75 Dart Sport with a stock 225 1bbl. Carb is shot. The parts houses are showing 4 different carbs. I know I need the bowl vent for the charcoal canistor. But, what is idle enrichment? It's showing one with and one without. Is that the idle screw at the bottom of the throttle body...

Does anyone know if a 73 Dart Sport AC/heater box will fit a 75 Dart Sport? I am not sure. Didn't they change the controls between those years? And if so will the 75 still work on the 73 box?

Does anyone know where I can buy a heater shut off valve for my 75 dart. None of the FLAPS show it has one but I know better. If I cant find one I wonder if a GM style will work?

I just got done putting the seats in the 75 DS and relized my 64 Valiant has more leg room yet is a smaller car. The 75 has a bigger trunk but man.. there ain't room for a small child in there. Does anyone have the cubic feet on the 75? Just curious.

Anyone have a trick or idea to get the rust out of drip rails on a Demon/DS/Duster body? Its at such an angle that I dont have anything effective.

I am racking my brain sensless on finding a vinyl paint that matches the factory blue on my 75 Dart. Has anyone matched it in thier restos or just get what I can and don't look at it? I hate to have the whole interior redone because the seats are excelent, just the plastic needs a facelift. Also...

I am looking for a non-tinted passenger door glass for a 75 dart sport. I am located at zip 37865.

I know there are several of us here on FABO that have a second gen Valiant that needs a rear window seal. You can get one for a barracuda and dart all day long but none for the Valiant. In fact everyone I have called says that "We get a request for one at least once a week" ..... THEN WHY DON"T...

Does anyone repro the reverse linkage for the hurst shifter? Brewers shows 68-up, and it looks almost right for the 64. Is it?

OK heres the problem. When you make a left turn or hard curve the engine dies. Runs great straight or when I turn right. I just had a new tank put in and a new 750 holley. I pulled the tank to see if anything is floating in there and nothing. Was the original tank baffled? I bought the new tank...

Hey I just found this on ebay. I shure wish I was on the left coast all you find here on the right is chivys. :sad2: It has a parts car too! Maybee one of you guys can jump on this. http://cgi.ebay.com/ebaymotors/64-DODGE-DART-GT_W0QQitemZ8057885419QQcategoryZ6783QQrdZ1QQcmdZViewItem

My a-833 overdrive does not want to stay in reverse. I rebuilt it. Replaced all synchros and bearings and re-assemble it by the service book. Before I put it in the car I went through all the gears to check for shifting/meshing problems and everything was ok. It went trough all 4 gears fine and...